Search:

You can remove the enclosure without removing the control panel. You do have to unbolt the arm from where it is attached to the main casting. I swung it to the side and suspended it from a large A...

Thanks for the files! I might have to bug you in awhile about doing the networking. First though I have to finish wiring up the home shop to move the mill into.

Good job on the restoration. I love the repaint of the factory "Torq cut". Is that something you would mind sharing with those of us that need to freshen up theirs on the outside? Cleaning out...

My X axis was noisy but no backlash before I replaced the bearings. The ball screw is easy to tear down, clean and reassemble yourself. However if you are fitting new balls I could see the cost...

If you can get one for $4000 that is a steel in most markets! I've seen working units on the market for 20! I paid $6000 for mine a couple years ago with a bunch of tooling and a very handy Midaco...

I have a Torq cut with a GoTek floppy emulator. Best thing I have done for my mill! Floppies were so unreliable. One time it would read just fine and the next time it would say the file was...

sorry, I was moving some files around in dropbox and that was one of them. Here is a good link. https://www.dropbox.com/s/ok6ywizsvhcmo66/SPINNERA.txt?dl=0

You are correct. The correct number is ZKLF 2575.2RS A bit of corrosion on my old bearing made it look like an E. At least I got it right when I ordered bearings!

https://www.dropbox.com/s/97rf1jvi4lom1q1/SPINNERA.txt?dl=0

Hey Steve. Feel free to use this program. Stock is 3x1x.325" aluminum. X,Y is the lower left corner of the part, 0 is the top of the...

Yes, I concur on the spindle noise. Sounds just like mine.

The ballscrew bearing is ZKLE 2575.2RS. It is a duplex bearing so there is just one on each end of the ballscrew. Let me know if you...

Anyone know how to get the controller to power on the Misc. Functions outlet on the side of the cabinet? Its on a Torq cut 22. I thought an M36 chip Conveyor might do it but no luck. I am hoping...

mine is in the cabinet.

Hey Marty, glad to see you got your mill up and running. Are you running it off of 220V Single phase? I am considering moving mine to my home garage soon so I can have easier access to it and I...

Hello everybody. I was wondering if anyone would be willing to share a couple parameters on there Torq cut 22 with me. I've been having following errors on the Y axis and X axis over current...

I found on page 62-5124 of the maintenance manual it give the procedure and torque specs to lock down the ball screw bearings. PM me if you don't have it.

I wish this thread was hear when I had to replace the oiling metering orifices that were plugged. I couldn't figure out how to get the table all the way over out of the way.

Any updates on the...

I hope someone can help me out here as I am about ready to burn this machine down. I have a torq cut 22 with the DX-32 controller. It works good for the most part but sometimes when it is executing...

So awhile ago I was upgrading the coolant pump on my torqcut 22. Unfortunately the circut could not handle the larger pump and when the fuse blew I was stupid and used the only one I had which was 2...

I have not done much with it yet as I have been moving. machinetek has not responded back to my PM I sent him. Hope everything is OK and he returns soon. He is an invaluable resource to those of...

thanks for pointing me in a direction!

So I am having problems with my torq cut 22. I believe the AUF board is toast. I have a permanent emergency stop activated alarm. Measured the voltage at wires 80 and 81. Nothing when the...

Any update on the repair services? I have a board that needs fixing and I was considering this same comany.

Hi everyone. I hope someone can help me out. I have a torq cut 22 that the previous owner put some used motor oil or something in the way lube tank. I noticed some of the lineal ways had rust on...

Hi Bill,

I haven't been on here in awhile so I missed it when you posted. I haven't looked too much into the probing capabilities of the torq cut as mine doesn't have the software installed. ...

Thought I would check up on you before heading off to bed myself. Glad to see that you are being a lot more optimistic. Your attitude plays a big part in being successful. Just keep swimming, just...

Pete, can you put a fuse on the 12v output side of the power supply? Cheap insureance if it is a board pulling on.

If your job market is like it is here, everyone is low balling their ads...

Don't throw in the towel on your dreams. There are to many of us on here hoping and praying for you. I'm sure there are countless people wishing for your success if nothing else because you are...

Let's have a pity party together! I just replaced my spindle my spindle encoder and now the belt is slipping on the excessively worn sprocket. A new one costs $400 for a part that should be $15. ...

That's great news on the mill. Simple things always fix the largest headaches. My bender die is a model 200. I think the follow dies are different but the main die might be the same. If it will...

I just got back from a 2 day motorcycle trip and now I have to get all caught up on what is happening on the interweb. Glad you got your PS back and so far it looks like everything is working. I...