Search:

Here is a free software that works with the D10/D6/D6B. run a serial cable to the control and match the settings in the D10 Hybrid and you should be good to go. I hope this helps!

Ah...yep that is it....then you serially connect it to the D10/D6/D6B.

Unfortunately the company that makes the D10 is no longer in business. The went away in December and there is no longer...

Here are the links to the parts my customer have used:

Femal - Female Adapter - USB

Amazon.com: USB Type A Female to Female Adapter: Electronics

Or

For only $0.96 each when QTY 50+...

I have seen this when the air pressure/air volume is restricted as well. First, watch the air guage on your regulator and see if it is dropping. Does the air compressor kick on as this starts to...

It states that it is free...but that is a 30 day trial I believe. Then after that it is 150.

I hope this helps.

Jonathan

Well, it is not free. this website shows it for $150.00.

Here is the link:

Lantek V27 - Mold - free-download|Unlimited|license|serial|unlock|keygen|free|activation|patch

Unfortunately no. I have not used Lantek in a very long time. but I will do a search for you and see what I can find.

Jonathan

What are the issues you are having cutting this material? I have cut plasma on Stainless, with the film without issue. Some times you have to cut a little of the film where you are piercing to make...

They now have a RS232 to USB Adapter available online. You can plug that into the Serial port of the control and it will access a Memory stick like a serial download or floppy. It works great and I...

Two options are available: Direct serial link using RS232 communications. this will require software. I suggest using DNC32 software.

Option 2: they now make a RS232 to USB Adapter for that same...

It looks like the right one. they are single acting. when you add air, they pull in. :)

You need to take all the machine grounds to the first ground rod. This will include the gantry ground, the legs, the table, and the plasma chasis ground. The chasis ground is an additional cable that...

If the Pendant is freezing up, this could be to that power loss I was talking about before, or it could be noise. How old is the system?

If you are getting this error during the cutting process, then I would look at the power cable going into the Command THC Module. It may have a loose connection. the VICON would still be outputting...

Thanks Jim! You have a Great Day!!

The leak is not normal. You should replace that air cylinder. I believe MSC carries that air cylinder. I will also upload the System grounding documentation given out by C&G Systems to show you the...

This forum has been created for general Q & A on CNC plasma and Oxyfuel Cutting machines of all types. Here we can help you with any trouble shooting questions you may have or onsite assistance if...

Just a thought...what kind of dedicated grounding system have you installed? what is the ground test? When you run a plasma, there is a great amount of RF Noise. This noise will play havoc on your...

Howdy Alan! Have a Great Night! :)

In the Drive box, you see the 3 cards that are the same, the bottom card is the sync card. take a meter, put it on DC volts. the red from your meter goes on sync and the black on ground. (the two...

on picture 201, there will be a chasis ground on each plasma system, the cable coming from the burny on the cable track bar, or the bolt underneath the burny, depending on the year it was made, this...

Open the cables manual, select Mustang, then plasma interface, then select the HT2000/Max200 listed in the list. This will show you the grey cable, the interface card and the connections. you will be...

The (4) grey cables will go to the (4) plasma power supplies. The grey cable has (4) wires. Red, Black, Green, and white.

There should be a small, 2" X 3" tan phenolic card wire-tied to one of the...