502,539 active members
5,471 visitors online
Register for free
Login

Search:

Type: Posts; User: cob

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    52

    how to take adapter off

    I am trying to see if anyone has any idea of how to take this adapter of ?
    is there a special wrench for this adapter or is it treaded ?
  2. Replies
    1
    Views
    138

    Re: Looking to buy a Brodgeport/Romi/EzPath

    Depends on what you are doing and what you need it for?
    If you are doing prototype this are perfect there easy and fast to program .
  3. Replies
    1
    Views
    55

    Indication a big I.D OR O.D

    Hello everyone
    so I am trying to see what or were to buy an attachment for a Indicator.
    I have these big I.D and O.D to indicate on a mill but my indicator doesn't reach
    can someone guide in the...
  4. Thread: unrolling a circle

    by cob
    Replies
    3
    Views
    104

    unrolling a circle

    hello everyone
    I am trying to see if mastercam can do this?
    so I have a 10 inch O.D with a wall thickness of .250 so I.D is 9.5 inches
    I am trying to see if I can unroll it (lay it flat) just...
  5. Replies
    0
    Views
    90

    overtravel on A-B- AND Z head

    maybe someone has had this issue before , so I tried to home the head on the flow waterjet and as it was doing it , it gave me a overtravel the issue I am having is I cant
    reset it I push the side...
  6. Replies
    0
    Views
    94

    flow waterjet height sensor.

    trying to see if anyone has had this problem,
    so when I start to run my program and my height sensor goes and touches of to my lead in it will DO that but when it gets ready to cut it just pauses,...
  7. Haven’t try not using the dynamic But I will...

    Haven’t try not using the dynamic
    But I will that shot

    So how often do you guys change the mixing tube?
  8. Re: how to calibrate the articulated head on a flow waterjet

    The screw resolution ?
    What do you mean by that and how do I do that?
    Actually when I cut small holes is when you notice it more this hose look like lemons .

    Forgot to mention is A axis left to...
  9. Thread: Teach function

    by cob
    Replies
    0
    Views
    203

    Teach function

    Trying to see how to work this function (teach function )
    Has any one use this if so how do u use it.
  10. Re: how to calibrate the articulated head on a flow waterjet

    Thank you
    I shall try that out and hopefully that's the problem.

    how often do you calibrate your tip?

    is it everytime you change you tip?

    thank you:cheers:
  11. Replies
    1
    Views
    11

    shoulder bolt supplier

    trying to find a place to buy shoulder bolts
    can any share where you buy yours from
    thank you
  12. Yea there’s a sleeve. So the way it is Is...

    Yea there’s a sleeve.
    So the way it is
    Is basically a mixing tube then I put the sleeve then
    I just insert the nut with the collect and make sure it’s all the way up
    And just tighten the nut...
  13. Yea I am trying to figure out how to line up the...

    Yea I am trying to figure out how to line up the A
    and B motors or how to calibrate so it cuts right
    My circle are about .010 out of round
    Thank u
  14. Replies
    6
    Views
    183

    Re: D2 steel sending to get heat treated or not

    So this punch that I am cutting will have a .750 I.D hole thrue and the OD will be 3.00
    Should I Finnish the part to size ?
    Normally other material we send out sometimes the id shrinks or gets...
  15. Replies
    6
    Views
    183

    Re: D2 steel sending to get heat treated or not

    I thought d2 was a good material to make punch and dies I thought it was a very strong material.
    do you guys have any sudjestions .
    I would like to buy some kind of steel that's very durable that...
  16. Replies
    6
    Views
    183

    D2 steel sending to get heat treated or not

    trying to see if it even matters to heat treat d2 steel.
    I am making a punch and die to press some parts have any of you guys dealt with d2 steel?
    should i rough out the punch and die send it to...
  17. how to calibrate the articulated head on a flow waterjet

    does any one here have a flow waterjet with an articulated head?
    I am trying to see what are the steps to calibrate the A and B motors
    how do I check to make sure it is line up at 90 degrees so...
  18. Replies
    0
    Views
    218

    were to find the trim command

    hello so I am having a problem with my DXF file
    when I load it into flow path I do the purge and it checks out fine but when I do the anylise you can see that there's a some RED lines so I ...
  19. Replies
    6
    Views
    403

    Re: dxf file not able to read

    please bare with me this thing can be frustrating at times
    thank you again
    so I got this slot that is 4 inches long with a 1 inch radius on each end
    when I hit the shift key to see if it chained...
  20. Replies
    6
    Views
    403

    Re: dxf file not able to read

    thank you for the replies
    so I am running mastercam 2018
    and yes for entities; some of them are not chained al the way so it will not let me do a toolpath
    some of the features that I am importing...
  21. Replies
    6
    Views
    403

    dxf file not able to read

    I am trying to figure out how to read this file (DXF) when I bring it into mastercam for some reason I try to click on certain points and it will not let me choose them
    is there a process I have to...
  22. does anyone use mastercam to progarm flow waterjet

    does anyone use mastercam to progarm flow waterjet
  23. does anyone use mastercam to progarm flow waterjet

    does anyone use mastercam to progarm flow waterjet
  24. Replies
    1
    Views
    6

    drops of sheetmetal

    hello everyone I am trying to see if theres a place or if someone here have drops of sheetmetal that they are not using (between .040 to .125 thick aluminum ) from 4inch up to 12inch

    its ok if...
  25. Replies
    1
    Views
    204

    vertify not working

    got this problem on mastercam cam for some reason when I do my toolpath I can see it on the backplot but when I go into the vertify I cant see the stock or even the tools
    is there a setting I have...
Results 1 to 25 of 354
Page 1 of 15 1 2 3 4