Sounds like you forgot to press the back up soft key before powering down, if you do not do it, the machine will load the old parameters back into the controller
Sendt fra min ONE A2003 med...
Type: Posts; User: Riddersholm
Sounds like you forgot to press the back up soft key before powering down, if you do not do it, the machine will load the old parameters back into the controller
Sendt fra min ONE A2003 med...
Hello Laurent. This is because the varibale limits you try to change is out of the systems encoder positions limits, If you go to the systems parameter you will see a + and - limit based of the...
It is not possible to check with out the special tool.
Please look at my cruede drawing to understand the problem regarding M drive rotation with tool holder out of allignment
...
This process is much more then what you say here, have you alligned the M spindel drive to the center of the holders when they are resting on the fixing pin? No because you need a special tool for...
You have a radial M turret, for allignment of this type of turret, there is a special realignment suitcase with reference master tools, the radial M turret is a B***h to do, and not possible without...
Hello sir.
Go to Parameter function.
Then press soft key "Display change"
Then press --> arrow on the soft keys.
Then press on the "Menu Change" button
Keep us updated.
Add a / M00 and press the blok skip button to make the control to skip all bloks with / infront.
Sent from my iPad using Tapatalk
Hehe I don't see my self as a "mysterious guy" but I see what you mean. So your 05 alarm is just that the machine is not ON "Start up sequent" your Y01. Y01 means you have a problem on your Y axis...
The ready button is what I call the hydraulics button next to the E stop button, the start up seaquens is quite unik for these machines.
Press the "ready button" twice - then press the "Clear...
It should but if i understand you correct you would run the transformer all the time, that is a saftey hazard, the main switch should cut the main Power to the transformer so it is not ON.
A 12AH...
Look at the control an tell me if it says CNC 332/432 or 532. Just open the door and turn the rod connected to the main switch breaker by hand or if there is no rod use a isolated screw driver to...
Heidenhain or Phillips control? On these old Mahos the battery change is normally in the electronics cabinet in a holder with 3-4 batterys regulere side D or C batterys? Just remember to change them...
You have a alarm for the main spindle motor fan, and for what is either low coolant in your tank or the coolant pump motor relay
https://www.bearingscanada.com/SearchResults.asp?Search=6006+RZ&Submit=Search
Here you go, don't know the sellers but seems fine.
I would not go ceramic on this kind of application
Dismount the spindle and see what the old bearings are marked with. If they are not marked dismount the bearing and show the internal design so it can be identified
Hello sir. I send you a Private message to try and help you and have not heard back, so please not leave before checking your inbox
No its not.
ATC position changes.
Base Zero point changes.
Turret Center offset changes.
Curvice coupling has to be checked.
In my region approximately 4500£
This is it. But these old cards are not available "New", you will have to upgrade to BL-4 card. Or buy a used
If you buy a new BL-4 the dips switch will be different
My guess is either and encoder fault or a Axis driver card. If the driver card and SVC card is the same on both Axis 50A/50A for example you Can Try switching then and if the erroer moves to the X...
In your Axis data page what is the RDIF/RCON and RAPA values on the Z Axis?
Well that depends on what you believe is problems :) But the new Machine is quite good, they have made some stupid design stuff but that is mostly for service People where that is a pain in the ass,...
It is a complet new design on the X-Y and Z Axis.
My guess is your beam sensor that tells the machine if there is a tool in the magazine pot, usually there would appear a alarm on this, but try cleaning it
Hei. Vis nogen af eg trenger help med noge må i sige til, eg er service tekniker i en af de store maskin forhandler og har jobbet med programmering i en del år før det. Bosat i Stavanger området. Til...
Check your power supply and fase direction
Hello. This Machine might Be worth looking at
DahLih DL-MCV 720 selges ? Plustech AS har n
In the disk you have a system data back up. That is your parameters. Did you change the batteri? If Yes how
If you would be interestet in a Nice Maho 400C with a Heidenhain/Maho CNC 332 then i know a guy in Denmark who might want to sell his.