Try Norman Ready 213-280-8376, [email protected]
Kirk
Search:
Type: Posts; User: kmuller
Search: Search took 0.00 seconds.
-
04-13-2015, 03:17 PM
- Replies
- 207
- Views
- 65,625
Re: Hitachi Seiki Service and Support!!!!!!!!1
-
12-23-2014, 04:39 PM
- Replies
- 1
- Views
- 1,103
Pressing reset changes G54 values to zero.
Got used Kitamura with 16i controller and when reset is pressed, the G54 values change to zeros. Is there a parameter to change this?
Thanks for any help. -
12-23-2014, 04:34 PM
Thread: G54 zeros on reset
by kmuller- Replies
- 2
- Views
- 1,356
Re: G54 zeros on reset
Thanks dcoupar, The issue is that when reset is pressed, the G54 offsets are changesd to zeros.
-
12-23-2014, 12:46 AM
Thread: G54 zeros on reset
by kmuller- Replies
- 2
- Views
- 1,356
G54 zeros on reset
Purchased a used Kitamura HX400ia with Fanuc 16i. How to stop from zeroing out the G54 when reset is pressed.
Thanks,
Kirk -
02-23-2012, 08:25 PM
Thread: Micon 16IIa
by kmuller- Replies
- 8
- Views
- 2,731
Dennis, I send the file to Scott Davis at your...
Dennis,
I send the file to Scott Davis at your facility. It is a backup file from a machine I no longer have - on the house. -
02-23-2012, 05:28 PM
Thread: Micon 16IIa
by kmuller- Replies
- 8
- Views
- 2,731
You are in luck. Checking thru the ladders I...
You are in luck. Checking thru the ladders I have backups for the last one I checked is 2685b02j. Send me your contact info.
-
05-18-2010, 10:38 PM
Thread: B axis halts machine
by kmuller- Replies
- 1
- Views
- 660
B axis halts machine
Fanuc 15 MB 4 axis - While drilling on Z, * shows up next to B on program check page and machine stops with no alarm, no feed hold. Drill at end of peck, ready for retract. The * usually means the...
-
08-06-2007, 07:24 PM
- Replies
- 3
- Views
- 1,093
Programming part variations with block skip
Is it posible with proman to post 2 parts with slight variations into 1 program and switch between parts using block skip?
-
07-31-2007, 03:08 PM
- Replies
- 207
- Views
- 65,625
His website is www.kmtscnc.com - you can find his...
His website is www.kmtscnc.com - you can find his contact info there.
Kirk -
01-18-2007, 11:14 PM
- Replies
- 9
- Views
- 2,453
Changed D30 to 60 in the G-data table and...
Changed D30 to 60 in the G-data table and everything is working great.
Thanks again Dale.
Kirk -
01-18-2007, 04:13 PM
- Replies
- 9
- Views
- 2,453
Thanks Dale, I found it the other day. You are...
Thanks Dale,
I found it the other day. You are right, it is in the G-data table. I'm adding more tools to the magazine today so by this afternoon I should be ready to change the data in the table... -
01-08-2007, 07:33 PM
- Replies
- 9
- Views
- 2,453
Navigating Hitachi Seiki HG400 w/ Seicos Sigma 10M
I need to locate the system table that includes the # of tools in the magazine. Any help would be greatly appreciated.
Thanks,
Kirk -
12-06-2005, 08:45 PM
- Replies
- 207
- Views
- 65,625
how to reset magazine sync
HG 400III with Seicos 10M control. Tool mag is out 5 pots. How can I reset? :cheers:
-
11-29-2004, 07:22 PM
Thread: Micon 16IIa
by kmuller- Replies
- 8
- Views
- 2,731
You already did, thx, Kirk
You already did, thx, Kirk
-
07-09-2004, 11:57 PM
Thread: Micon 16IIa
by kmuller- Replies
- 8
- Views
- 2,731
Micon 16IIa
Lost all data and parameters on main board. Hc-400 s/n 40546 Software # 2685B02J. Mori Hitech claims they can only re-load the sotware on site. Similar problem occurred 2 yrs ago - Hitachi able to...
-
01-14-2004, 10:54 PM
Thread: correct pallet check
by kmuller- Replies
- 0
- Views
- 1,183
correct pallet check
Hitachi Seiki HG400 III w/ Fanuc 15M. Want to write macro to insure that the proper pallet is in for running 1st or 2nd operation. Can't find data bits. Any ideas?
-
11-07-2003, 06:21 PM
Thread: Hitachi Seiki MH 400 drawbar tension
by kmuller- Replies
- 1
- Views
- 1,456
Hitachi Seiki MH 400 drawbar tension
replaced disc springs - still not enough tension
Results 1 to 17 of 17
