Okay I've fixed it.
First off, I had to totally disassemble TRP mechanism, clean the cylinder and piston thoroughly, polish them (cylinder had smaller scratchmarks on couple of places at the top...
Type: Posts; User: allenp
Okay I've fixed it.
First off, I had to totally disassemble TRP mechanism, clean the cylinder and piston thoroughly, polish them (cylinder had smaller scratchmarks on couple of places at the top...
Actually I think I'm wrong although this might be a small problem, but I think it's not causing this because when you just press on Tool release button it doesn't orient spindle and this air loss...
Ok I think I've found where problem lies but I'm still not sure.
I've noticed that when you turn spindle orient on (M19) little pin (about 12mm in diameter) which signals the machine that spindle...
Ok, I've tried fixing it, no luck. I tried putting small amount of air tool (compressor) oil to lines, both to machine and left and right of the tool release solenoid. No luck. Then I removed and...
Hello, don't ask me why, but I would like to connect additional wire from tool release button on spindle (Z axis) inside machine and not the one on keyboard to an optional M code relay like this:...
It was extention I/O module at fault, replaced all three of them and it works fine.
Hello
recently we found on power up that alarms given in title occur every time you turn on machine.
Here are some ladder pics during alarms
https://ibb.co/kqYJcxq...
I still think it is, because I've removed encoder cable from X axis motor, dried out pins on both end and put some PTFE band on the threads, sprayed contact spray on pins and inside connector, dried...
Is there a way to see in machine diagnostics X axis encoder cable data being sent or not sent, also cable connection pins which work which dont?
I believe there is a problem with X axis encoder...
Hello, we have this machine which sometimes when turned on will throw this alarm 300 APC - X axis need ZRN.
Meaning it lost reference for X axis, but normally when batteries which hold axes position...
Hello,
can these alarms be found in ladder logic?
I know I can find alarms like 1003, 1016 etc, but these spindle and servo amp related alarms, can they be found in ladder logic somewhere?
Or do...
Regards from Croatia,
I have a question about a woodworking machine, Macpol Speedy 2,
my colleague bought this machine and now he has a problem with his graphics card or mainboard, his...
can you help me with this and guide me step by step, because I seem to have same problem, but cannot find what you've found to solve your problem?
thanks in advance
Thank you so very much!
Hello guys,
we've got Stama Robodrill MC14 with Fanuc16i and intermittent errors 1018 (TCZ switch is welding) and 1016 (MCC is deffective).
When I'm looking at alarm 1018 in ladder I see it...
Alarm appears right away, umbrella hasnt even moved yet a bit...
Hello guys,
is there a way to download backup for this older machine like you do on newer ones? What is the procedure for that?
Secondly, what can you see in that backup and is it possible to...
Hello, is it possible to manually recover or test tool changer like on older VF2 (not SS) series machine by using "Debug" mode?
I don't see any option on the new control to do this, there is no...
Ive tried this. It didnt work because it didnt finish contour. It didnt crash in part at the end but it didnt finish it either.
Machine is older, it is actually Mikron Haas VCE 500, but the control is very similar/equal to newer Haas mills.
We have problem with this machine that it doesnt finish contour (toolpath) very...
That is not the solution its a patch. I want to fix machine not change gcode
Nope, that is not true. Same program on newer machine doesnt have this problem
Machine is older, it is actually Mikron Haas VCE 500, but the control is very similar/equal to newer Haas mills.
We have problem with this machine that it doesnt finish contour (toolpath) very...
Okay thanks, I will try it, but that is not the solution for a problem it is a patch.
I would like to know and understand why machine does this, where in the control is logic for it, where in...
It can have and it does have h2 and d2. You just need to edit. I worked with that since beginning
No that is not correct for t2 is h2 and d2
Hello,
we have this problem with this machine for long time now, I've tried getting help from official supplier multiple times, no luck, they just don't have expertise to understand what the problem...
Okay the problem is solved!
It was one parameter "missing", or I could not input it at first because it showed me message to confirm input of the parameter data with "Delete" key, which I thought...
Okay the problem is solved!
It was one parameter "missing", or I could not input it at first because it showed me message to confirm input of the parameter data with "Delete" key, which I thought...