Search:

Hi
Our VMX42 when starting will not start, ie turn power on all, good then when selecting manual and start nothing happens?
Anyone out there had this problem?
Regards Burgs

All sorted some idiot who shall not be named, did some searching in the control cabinet and had managed to knock the video cable out (chair)!

Burgs

Re: VMX42 Monitor MAX 4 Single Screen
Hi All
Replaced the monitor supplied by Tsubis had to strip the supplied monitor down and fit into the original housing.
Removed the video card, stripped down...

Hi All
Ok one step forward and one backwards today, fitted a new Philips monitor and still no go, so video card is the problem.
Removed the video card, stripped down the monitor housing that was...

Hi Afshin where are you located?
I located the manuals today but didn't look at what they are when you said your controller was a 532.
The manuals I have are in English.

Burgs.

Ok is your machine a goer?
If I find the manuals what will be the next step, where are you located?

Hi
Mine is the 432 controller so not sure it would be any use?
Burgs

Hi
Still having problems, supplier has told us to gut the old monitor, break the mounts off the screen supplied and cut up the housing make his screen fit.
Boss is not interested in doing this but...

Hi
I will have to check what I have, there is some training information on operating the MH880C and another smaller separate manual that could be training but I have not looked at them for some...

Hi
Thanks Powerr, we have sent him numerous photos of the Max 4 single control inside and out side, plus some more today.
I could not find a Hurco single screen part number in the parts manual for...

Hi
How did you go with the manual and which one did you need, operational or technical?
I also have a 1991 MH800C with manuals but it would take a fair amount of work to scan and send them, so...

Hi All
Our VMX42 MAX Single Screen build date 2005, monitor has failed in the past with the previous owner, he then had a 240V computer monitor fitted over the top of the original monitor.
The new...

Hi Bloke
Thanks for that, I wil give it a go today all being well, it's electric.

The oil is heavy 120 to 150 ISO, I could not find that listed in any of the manuals I have?

Best Regards
Burgs

Hi Powerr
I think I have worked out the oil levels, the top one I was looking at appears more like a scribed line for the timing, I can see switches and gears behind the Perspex window.
The tool...

Hi
The main breaker on VMX42 has broken the gear mechanism that opens and closes the breaker, plastic bits of gearing came out and we cannot isolate at the breaker.

Can the front section that...

Hi
My 2007 VMX42 is leaking oil out of the tool changer gear box, or around the shaft the arm mounts to (24 Pot tool changer).

Looks like I Have to replace the seal and the o' ring and then reset...

Hi
All sorted found where the cable went with help from Hurco Singapore techs they also sent through parameters and it turned out that one of the parameters was not right changed it and away we...

Hi
I need to set up a DNC link to my Hurco VMX 42 (2005 build), there are two RS232 Port on the control cabinet, Port 1 when I trace it back to the computer is not connected, see photo, so I...

Hi
Thanks for the reply, looks fairly straight forward to change, you wouldn't know the thrust bearing numbers by any chance?
Might also get the ball screw repaired at the same time, to make sure...

Hi
I realise this is an old post but I have a noisy Z axis in my Tornado 200, and suspect the chuck end bearings of the Z axis, the lathe is still holding good tolerances but very noisy in rapid...

Hi CamSoft
OK something must be amiss, I will have a look at the emails I have sent as many of the issues have been solved, others are still hanging.

I have sent another email this morning...

Ok
Did that and I have CNC loading again.
Quite a few issues as last backup that I was able to use was 3/01/2018.
The Inputs are showing up on the diagnosis screen as being all on?
Operated the...

Hi
Karl
Hopefully the computer is OK now just need for CamSoft to come back on the error message,
The index/reference markers are in the linear encoders.
From the Heidenhain information
•...

Hi Karl
The single limit switch does both ends of limits so cannot move it (could possibly make a different ramp each end a bit longer so it triggers the switch earlier) , but the index markers I...

Well Learnt more today about computers, another wire was off, this time the hard drive, so have lost most everything, what amazes me is it is hard to pull the plugs/wires off and put them on, might...

Hi
Thanks for the reply's.
Karl
The end of axis switch wasn't my first choice, I could put a switch either end but, I might save that for now and try and set up off the index markers I am pretty...

Hi
I have restarted work on my long term project MAHO MH800C, 2 spindles (horizontal & Vertical), 5 axis, 3 linear 1 rotary, one swivel.
The 3 linear axis have only one switch for limits, that are...

Hi All
Thanks for all the help, machine now up and running :cheers: ran it through the warm up cycle, carried out some tool changes, now to tidy up and fit covers.
What I found with the Power On...

Hi Bloke
do you know which pin is 0V?
Can not find any decent electrical schematics anywhere in my information.
Checked all BIOS and parameter settings and reset to data supplied, restarted and...

Hi
Yes I believe so, but will check again in the morning incase I missed something, looking at my notes there was a couple of things different and I am not sure now whether I changed them or not!
...