Search:

Only one mill, anyone sell a reasonably priced kit. Or want to make me one.

Does it require a new motor, or do you use your old one.

If anyone has a metal version of the upper drive gear that meshes with the drive motor I am in need. As the plastic one stripped all the teeth off.

Thanks Dennis

:D giving it a try as well...

Any idea why they have it then...

I just purchased this mill and have a question... On my mill just in front of the HI-LOW Gear Knob there is a sight glass , it does not make any reference to this in the manual or even show it in the...

If you have all your settings dialed in there will be no dross, or next to none, post up the settings you are using ,perhaps I could help you out.

Sounds to me like you have some trouble with the code you are producing.. I have an Icon 4x8 table and it rocks, I use to have a table from Precision Cutting Systems out of Calgary Alberta.. That was...

Try 40 amps , .o9 cut height, leave the pierce height the same and speed up to about 70 in/min:) Also now are you setting your air pressure, make sure you put the plasma unit in the purge setting to...

If you live in the USA PaulDON56 why does your Profile say you are from Alberta Canada... Whats your real name .....If it smells like a Rat it is a RAT...

I would not give 2 cents for another...

Yes, but at least Toyota is looking after there Customers.... And some Toyotas are cheaper than CNC Tables..

Morvaman , you could be right there , I ordered a 4x8 Icon series table and It is running candcnc setup. I never paid attention to what they where running there new G6 table with... All though they...

Edwardo, actually they run CandCNC controls.

Sold mine! Lucky Me...

I would give FastCut a call , I made a purchase from them and there tables are top notch!

Then maybe Bert needs to go to cnc school :0)

I just purchased a table from FastCut CNC, had a demo on there machines last week. Demo went real well. My table should be ready in a couple of weeks.. Will let you know how it works when I receive...

Thanks again Jim for the quick reply... I will do a little more investigating.

Jim, want your take on the Thermal Dynamics A80... Good , Bad, ???

I would like to see a Sub Form started for Fastcut CNC owners , I recently Purchased a table from them... Ordered my table today as a matter of fact. Would like to know if there are any other users...

Well at least the thread title is correct, (This Is an awful Story)pretty much pointless, if you or your compamy has 400 large to spend and can't find a Cutting setup , you wouldn't be in business...

I got the shipping quote from a company in china the builds small ATV'S thats what they would ship a container for... they never mentioned any thing about rental...

Shipping a 20 foot Container from China to Vancouver will run you in the 1200 dollar range, So its best to fill it up... Looks like an all right machine... You shouldn't have to worry about voltage...

Keep in mind those settings are with my Table, Plasma Unit , and THC... Your setting may differ... Use only as a guide at best, always do a sample cut on scrap first! Thanks Dennis

ipm 60 , arc current 52 , arc voltage 120

Make sure you buy the new version DHC2 ... I here it is far better than there older version!

I have Corel Draw, Viacad , and just got Plasmacams software... For simple shapes Plasmacam is by far the best!

I cut 1/4 plate with Fine Cut consumables with my hypertherm 1000 , does a nice job!

I purchased a table 4x4 with a single sided gantry, I can easily load a 4x8 sheet from the side and it can hang over each end.. It cuts a full 4 feet in each direction. So if i want i can cut my 4x8...

I find with my Hypertherm 1000, that I ran into the same problem... What was happening to me was once in a while I would get a little bit of slag on the torch tip, torch would go down to the plate...