Search:

I was injured a while back (still am) and haven't even looked at the laser in about a year. I finally got to the point of getting out to the shop to check on things. I didn't quite know what to...

There are some great alternatives especially for laser cutting.
The western machines are known for exceptional engraving.
For cutting the Chinese machines do a wonderful job
Talk to Nolan at...

Take your nose cone off and try that last shot again.

Gozzie

Boy aint that the truth. I saw posts that say you can get pretty close by measuring the length and diameter of the tubes. A person could probably search that
fairly quickly. You were very wise to...

I try to tell everybody to set aside a couple of hundred dollars for unknown extras.
I have to say though that's a first time I have heard of DHL doing a misquote.
Myself included there are quite...

Hello Alxx,

Listen to Nolan above. He is very good at his job. If you go the Chinese route talk with him.
I can verify that 18mm ply will be a no go unless you get big power.
Big power means...

I suggest everyone use the amp meter to know what 100% power is.
I cant imagine how many tubes have been burned up over powering them.
Then once once you know what is 100 % I would back off to the...

I really admire your persistence. I cant imagine how frustrating this is for you.
Don't give up. Maybe it does need an exorcism. Darn those demons.
I really wish I had something to offer other than...

Make sure you are focusing correctly. Whatever the lens manufacturer recommends.
And the make sure you are focusing that distance to the lens and not just the nosecone.
(50mm lens is from lens to...

Do you have any pictures to go with your guide ?
I would love to see some photos of the target fixtures you use and how you mount them in front of the mirrors.

Gozzie

You say there's a crackle or arc somewhere. Maybe in the power supply itself.
I know it would suck to have to buy another supply just to find out. Maybe you can take
the cover off and look for...

Just checking on your progress.
Did you figure it out ?

Congratulations on your purchase. You made a great choice. Shipping by DHL will be smooth for you too.
Keep us all informed along the way. I always enjoy reading these reviews. They are very...

I don't think anyone would argue with that. The damage was done and for that I feel bad for Keith.

That being said I think Thunder Laser did the right thing by publicly announcing that they were...

Yes take precaution on the red wire from the tube. Make sure it is high voltage wire and or encase it in a silicon hose tubing
and try to route it away from the other wires.

I don't think you...

Well you have partially isolated your problem and can narrow your focus.
The first thing I would do is make sure the power supply and the controller are on the same power feed. Not the same circuit...

Good job Thunder Laser !

This situation is what makes one company stand above the others.

This is King, general manager of Thunderlaser.
First, I must say sorry about this unhappy case.
...

It's a real catch 22. Do your homework and try to make your best decision.
It's amazing the different responses everybody has on every vendor in the world.
Seller A has many happy customers and...

Turn off the laser power supply or unhook it and see if the machine runs correctly.
If it works properly without the laser then you may have a brown out issue of sorts
where the incoming power is...

I am eagerly watching this thread along with many others.
I hope it ends with a positive outcome.
Reputation is everything.

Gozzie

You may want to search the forums for used machines too.
Many people start out with a smaller machine and decide to upgrade. You can take advantage of that and get a good used model.
There are...

Exactly David,
I was wanting an all purpose machine but leaned more to the cutting end. Most will say that 80 watts and below are best for engraving.
130 watts is pretty hot for some materials. I...

I'm sorry I cant help much in that area.
Honestly I don't think you need to spend your money on a high quality machine for what you are doing.
That being said I cant really recommend a low budget...

If that's all you really intend to do you can get by with a relatively inexpensive setup.
Small table and 50-60watts would be more than plenty for you.
Anodized alum engraves nicely without a lot...

I play with dollar tree foam boards for making foamie planes. Just for pure fun.
I am by no means a pro at this but with my 130 watt I have a couple of settings for different uses.
I know you...

Hi Nolan,

I sent you an email with her information.
Judy is a great lady as well as the Vice President of ER Hawthorne.

Gozzie

Good deal. She is already familiar with Thunderlaser and their operations.
It will go nice and smooth for you. She will always instantly reply to any questions you may have.

Gozzie

I used ER-Hawthorne based out of Houston. That was the closest port to me in Arkansas. You should look up the closest port to your location
to get the best trucking charges from the port. I found...

Here is a discussion on the issue
Frustrating laser engraving problem

There are several others also if you do a search

Gozzie

If you are cutting through in one position of the table and not in another position it just about has to
be an alignment issue being either at the mirrors or the table, especially if it is...