T5 x 16mm
Type: Posts; User: mick41zxr
T5 x 16mm
I have the same spindle, I rebuilt it with precision angular contact bearings & kluber grease.
Will hold 8k rpm (spindle max) sustained with relatively little temperature rise.
Rebuild is easy to...
Completely Agree with CL_MotoTech. I have two machines one with closed loop steppers the other with DMM. While I think the DMM better it is also overkill on this class machine.
The biggest...
No comparison really. The DMM is a far superior product.
It really comes down to your budget and what you are trying to achieve.
Please don't mix up the torque ratings when comparing motors....
Hi does anyone know a good source of soluble oil / cutting fluid locally in Sydney outside of H&F.
Thanks
Mactec54 that's my hand, yes its a complete Spindle Servo with encoder feedback. I was referring to the driver in the link posted by Raychar1234.
Regards,
MB
That motor looks to be a Servo spindle driven by a VFD, doesn't appear to have complete closed loop control.
I have been testing a complete Spindle Servo with Driver that will accept a single phase...
Mate at 1400x1000x1000 rails will be a substantial machine.
For instance my machine will be 500x300x350 travel. with x rails being 950, y 600, z 600.
Frame alone before epoxy is approx 600kg....
Also in regards to enclosure don't stress too much.
On previous build biggest noise was the blow off valve on my air compressor & if a tool chattered in a corner.
Regards,
Michael403034
With access to equipment you have your project is certainly possible.
I used multiple tube (10mm wall) boxed & welded together. 25mm flat bar for rail mounts. Head was multiple laser cut 10mm plate....
Yes power will be a problem, especially on the spindle. Faced the same issue on current build. Most dedicated spindle motors are 3 phase.
I am testing one now that is single phase 2.2kW 8000rpm....
Half way through building pretty much as you describe, however I would suggest as others have suggested & retrofit an existing machine. they seem to be plentiful for reasonable coin states side....
Currently looking for exactly the same thing.
There are a couple of VFD's that can run PMAC motors & servo's. But finding the correct duty motor is not easy.
Azalin,
On the Arel page there is a...
Not wanting to hijack previous thread, I though it would be better to post questions to a new one.
Eldon_Joh mentioned in Spumco's thread...
Eldon Joh,
Would you mind expanding on what you mean by re-lacing the wires. I assume this is all done within the terminal box, not rewinding the motor.
Do you get the same torque at lower speeds...
On current build (BF20L clone conversion) I am running a 80 frame (1.1kW) 2 phase WEG W21 Motor with SEW inverter.
Using PolyV belt. Getting approx 5000rpm at spindle, limited by some sort of wierd...
Ralph,
Looking to do a similar setup to your current one. What is max size end mill you can currently run in Al?
From what you have stated your running max motor 5000rpm at approx 180Hz
Regards,...
I have come across a barely used Hitachi SJ200-055HFEF (5.5kW 7HP) at a good price.
However I only have 240v single phase supply (Active/Neutral/Earth).
Can this drive run a 400v 3 phase motor with...
I was looking at the WEG W22 Motors, come in 2 pole with class H insulation. My main concern was spinning the bearings & armature that fast.
Also looking at performance curve the motor is derated to...
Thankyou,
From my calculations 3hp would be sufficient. When you say 'better VFD' do you have any recommendations? Yasakawa, GS3?
I only have experience with SEW drive which is a V/Hz drive,...
Thanks Mactec,
I think with my supply that the limit may be around 3hp, I am still not sure if a VFD can give me accurate orientation for a tool changer down the track or if this can be chaieved by...
Thanks Goemon,
This is installed in the shed behind my house. Unfortunately I am limited by cable size (underground x 40m) to said shed, but could push it to 20A.
I have an 80 frame WEG W21 (1.1kW)...
Has anyone had any experience with the Chinese Spindle servo motors & drives?
I only have 240v 15A single phase power available & looking for a high speed spindle motor for predominately machining...