Thanks Mike
Type: Posts; User: juniormachinist
Thanks Mike
Im looking for Motion Link software to communicate with a VFS5 Kollmorgen drive does anyone have a link thanks
Where are you ROSSITERENG
Hi Mike just got in to work and checked again the light on relay CR13 stays on and does not go out when we run the spindle or get the error message is this right or wrong
Hi Mike you mentioned in a previous post check that CR13 is turning on an off. this stays on does not go off is this still ok
Ok CR13 is on and stays on all the time here is the io screen pics 1 before start spindle 2 spindle running 3 stopped error message Ive have watched the servo display and it shows the spindle speed...
It knows where it is it positions it self for a tool change
Not yet the I got the servo display up reads zero in the rpm so is there some sort of speed sensor some where
Ok almost there with this thing now im getting this message 314578 any help would be appreciated ive nearly had enough of this thing
Thanks Mike dont sell yourself short your 2 cents worth is worth big $ to us turns out the home switch will show in the io screen on initial start but to see the ot switch the on button needs to be...
we think this machine has more than one problem trying to solve one at a time it had over traveled in the y on inspection the switch was physically broken the wheel broken of impossible to use we...
Ok so we got the new switch and we still have no limit switch signal on the y axis the switch is good also checked the wiring back to the plug on the input board and all is good do you guys have...
we are waiting for the switch to arrive and fit to see if there are any other issues
Thanks for your help will let you know what the problem is if he can find it
309376[ATTACH=CONFIG]309374
Ok so turn the power on at back of cabinet press the green on button soft ware loads up everything says ok check the lights on the drivers one green and one red on all 4 I get someone to release the...
sorry stuck an extra i in there and cant get seem to change it
sorry mike all the low voltage lights go out I have the prints will check today we were able to turn of the a axis
Attached is a picture of the pendent
Also the red light is on for the z axis on the pendant
And says z axis not ready on the pendant
Recently picked up a secondhand cincinnati sabre 1000 with a acramatic 2100e controller and 4th axis included
When machine is powered up we get a " Alarm 39-6 axis drives are not enabled" message....
Hi,
I am currently using mastercam x6 for solidworks and I notice when I want to insert tabs the option to do manual tabs is ghosted meaning I am unable to select the manual tab option and can only...
You might be able to change your safe height
Sent from my GT-I9505 using Tapatalk
we are trying to machine a ramp on a part using mastercam x6 for solidworks. when it is machined it leaves a step at the bottom of the ramp and we can't get it to go deeper. If you look at the image...
can anyone recommend a speed to run spiral taps at. we mainly use 6x1mm, 8x1.25mm and 10x1.5mm. we are using compression/tension type holder
thanks
Does changing the format mean that it chamges
- - - Updated - - -
Does changing the format mean that it changes weather its imperial or metric
our pitch is right. all the numbers in mastercam match whats in the nc code. it outputs g95
i have attached the same file we were using which is a 8x1.25mm as well as a 6x1mm file
we have a 96 fadal VMC4020 with a cnc 88HS controller and are using mastercam x6 for solidworks
we have recently began using tapping and have had limited success. we discovered that the feed rate in...
it didnt really help much due to the fact that im using mastercam x6 for solidworks its a bit harder to find and i would like a free tutorial or as a cheap as possible
I've already done that but I can't the tool paths to work
how do you do 4 axis machining on mastercam x6 for solidworks?