Search:

hi

i have a haas tm1p with 10tool atc
the machine is leaking alot of air way more than normal from the top of the spindle unit, under the pully area. it leaks more air from the top than the...

hi
does any one have info they can post here on how to setup and tune the servo motors on an I80 control from the parameter setup screen

ie, how to set the U offset and V offset values to get a...

sent on an email, 2 manuls hope it solves your problem

HI
does any one have a PDF version of the Mitsubishi CNC Meldas 300 Series Maintenance manual they can share?
looking for the one that shows the option cards and pin out info etc.

any other...

Hi
i would like to have an Mcode added to our Yasnac i80 control, so i was wondering if any one here new any one in the UK who worked on I80 controls that could do such a thing?

or if any one on...

you might find this alittle helpfull
https://www.youtube.com/watch?v=qsrMkde23s0

seems the PSU in these are abit more than power supplies they need to give other things to the drive to say all is...

Hi there,

i have a Matsuura with a yasnac i80 control

if i wish to take the 4th and 5th axis of the machine, can do i disable them in the control so it does not look for them until i put the...

Hi there

can someone please tell me what the steps are to make a full backup of a control running a MELDAS 300 series control. backup the parameters, macros etc

have looked in the manuals back...

HI, thanks for the reply,

i am putting a thread on the shaft, and threading is working just fine never errors and pitch is good so is the finish on threads.
i know it has had a new Main spindle...

Hi there,

on our citizen L16 machine i am trying to use the spindle index function to mill some flats,
control is Mitsubishi , Spindle drives are Mitsubishi Z200
every now and then the control...

i will try and find a old backup off the config files and PLC file, as we changed the drive to a yaskawa drive in the end much better drive, does have the custom spindle firmware installed too
...

Hi Guys

right, Yaskawa kinda said they don't think they could drive this motor good enough to say yes, plus the spindle orientation option disables all the PM stuff

i did contact Parker SSD as...

i found in this catalog from yaskawa website
A1000 Drive

Speed
Control
Range
1500:1 Closed Loop Vector (Inducon and PM Motors)
200:1 Open Loop Vector (Inducon Motors)
100:1 Open Loop...

hi guys

thanks for all the reply's interesting reading non the less explains quite a bit
should be noted this on a Milling machine so spindle orientation is also required for tool change just to...

Hi there,

we have a Siemens 3phase spindle motor and im looking for a drive to drive this.
now as it says on the name plate
3~ Permanent Magnet Motor

am i right in thinking we need a drive...

HI

i would like to know if there is a parameter in a 10M to change the Absolute Position to show with tool length included

as right now, Z absolute on the display figure does not take into...

Hi pete

in the USA Eston importer is
Anaheim Automation - Your source for Stepper Motor, Brushless DC Motor, DC Motor, and Planetary Gearbox Products
i am using the Eston EMG motors with there...

hi pete

as your machine is very much the same to my leadwell check out here for some build info for my retrofit, some vids too
...

hi lee

nice retrofit

just wondering what VFD you went with?
as on our retrofit we had to replace the spindle drive, was a Mitsubishi , replaced it with a Invertek plus 3GV, but found it no...

sorce file is also there by the way, so if you need to mod it you can.
i will soon mod it to make a random tool changer version with precalls

i aim to do a lathe version too but time is short...

here is link
EMC Documentation Wiki: Cam Post

check wiki i made a camworks post and use it on mills every day with emc running from camworks 2011

rob

i think with EMC you also have to think what has been done feature wise that is not even in the main EMC release profiles that people have programed them selfs?

like one thing i did on a machine...

any one find a solution to the E9 problem as i did not and gave up in the end went with adifferent drive and motor

rob

i have done it, bidirection ATC i think i put some info on the Wiki but if not let me know

EMC2 Spindle orientation with VFD - YouTube

see here some very quick dirty vids i did never had time to do anything proper
http://www.youtube.com/my_videos?feature=mhee

my 2x lathers are littid odd from normal as twin turret,

currently...

forgot to say

drive is on a Siemens 810T on a CHNC 1

Hi

can someone please help with a manual for a A06B-6055 Spindle Drive
looking for Pin connections & if possible also paramiters for drive.

thank you
Robert

Hi

got a MR-J2S-70A

i have wired it up per manual on Single phase 230v
it turns on fine, gives error "Servo Emergency Stop warning" AL E6
which is fine.

but when i close the estop switch...

hi
under the pass options is a Reverse Order, tick or untick this and it will change the start order around for you.