Search:

HI ALL
I have an Akebono CNC Machine with Fanuc 11tt Control.i have lost Parameters of this machine.But i have Parameters Manual but
i lost Timer Counter Keep Relays.is any body can help...

yes i have original parameters book and manuals of this machines
i shall be thankfull to you if you help me
[email protected]

Thank you ferret
i was hopeless because no one was replying me about my problem can u tell me that how can i enter the code?can i enter 1,s or 0,s in diagnostic page?and do u have diagnostic...

Hello All,
i have a CNC Machining center of Leadwell MCV 550E with Meldas M0 Control when i buy this machine there is no parameters in it but machine builder original parameters was in the CD and...

Hello Rai
I have parameters of Cincinnati sabre750 contact me on [email protected]

glend
then is there any solution for this machine.plz help me

Hi All
i have leadwell machining center of MCV 550E with meldas M0 control when i initialize it and send parameters then when i power
off and one the digit of x axis y axiz and z axis going to...

Respected sir guhl
Sir i have need fanuc 11m parameters of beaver cnc machining center i dont know what is the model but x axis travel is 1000mm
plz can u help me i shall be thanks full to u

Hi All
i have a CNC Machining center of Beaver with fanuc 11m control.Error(E) is showing on mother board i think if i initialize it then parameters will be lost but i dont have parameters detail x...

Hi All
i have a cnc machining center of leadwell MCV 550 with Mitsubishi Meldas M0 control actually my batery was dead on gx54 board so that i have lost parameters any one can help me that how can i...

HI ALL,
I have a Problem in my cnc turrning center Tsugami.problem is this that when i want to zero my turret but turret is not going on zero possition.and also our spindle is off .i was seeing...

hi unassumption,
YCM is the good brand i am related cnc maintenance and here is lot of YCM machines.and ther are working good if you want to buy then you can buy because this is a good brand

hello sir,
i am zain ali from Pakistan.i am doing cnc maintenance last 12 years i want to go abroad for work can you help me to searching the job of cnc maintenance in iran or dubai or saudi...

did you checked the crt and also ram status?

you mean that your machine is not on spindle servo drive it is on electric contractors for CW and CCW.?

hi this mean tha may be your CRT in trouble,or may be you memory section is not initializ.pul out tha rams to board and install again,i think you will clear,
but inform me please

hello martin
are you still need parameters of interact4 TNC151 if yes then please contact me on [email protected]

hello faiz how r u i am zain ali from Pakistan and i am doing troubleshooting of cnc machine in Lahore.id is [email protected]
cell number is +92-332-4244023..please contact.

hi igorko
if your CRT not going on when you push the on switch then may be your memory section disturb.if you have your machine parameters then you can machine on with delete and reset and cancel...

hi igorko
if your CRT not going on when you push the on switch then may be your memory section disturb.if you have your machine parameters then you can machine on with delete and reset and cancel...

dont worry and keep work you will be successful this is a good choice

do you check your RS232 setting in parameters?i think this may be fault of your setting.tell me that do you have checked it?

Hi jolulank

Are you really need parameters of Mori Seiki with Fanuc 10t,qre you seriouse or not.i have parameters and also manual if you want to buy i can give you parameters is just 70 US$ and if...

is your problem in now ok or not

Hello
are you checked the Limit switch
and emergency switch and also error
and see OT Switch or not

i think this is not parameters fault.you can check the limit switches because if the display is showing not ready then you N.C is not ready.check limiti switch or check that if there is O.T switch...

Hello crmb
do you mean that yours drives are ready and your CRT dispaly is normal but machine is not moving?check the pc parameters.and tell me that is you display of machine is in normal condition...

Dear sir guhl
please send me the spindle drive unit parameters.

Dear Guhl
yes i have changed all parameters.and when i changed these parameters then spindle running in M03 command but M04 is not working proper when give M04 then spindle move clock wise to...

sir i have change these parameters of spindle unit

F01 0001 F19 0010
F02 0000 F20 0040
F03 ...