Search:

Hi Bruce,

I was wondering if you were ever successful in getting this project to work properly. Just bought an Arduino Mega and want to use it to control a rotary table. I have the stepper driver...

Yes I still have the manuals. Sent you pictures in Private email.
Thanks,

Dan

I have the operating and maintenance manuals for a Fanuc 10M Mill system. email: [email protected]

O.K. guys,

I've stripped all of the Fanuc 10M controls out of my mill in anticipation of installing the Ajaxcnc control. I've listed some of the parts on ebay so if your interested just search for...

Gentleman,

I would like to thank you for all your input into my problems on the Fanuc 10MA. Unfortunately I'm at a stalemate. After much deliberation, I have decided to change out the control to...

Thank you very much for your input.

I traded what I thought were the three chips you suggested to interchange. Results were not good. I now have the problem in all three axis. They are all...

Gents,

Thank you for all your input these past few days. I haven't been checking my post for awhile and I will most certainly be checking and following up on my machine. I was working on it again...

O.K. it's decision time! I've been working on this controller for over a year and I have it almost there, but I don't know where to turn for this problem with the "y" axis. See my earlier posts for...

Hi Greg,

Have you had the chance to review the parts list I posted and come up with some suggestions for the erratic behavior of the Y axis on my Fanuc? It's sure funny that it only happens on the...

Here are the build details on my Comet Milling machine indicating the board numbers etc. I found this very faded sheet in the machine cabinet and was able to read most of it with a magnifying glass....

I'm so sorry Greg. There's no excuse for my slip up. As always, I appreciate your help and will be in touch for those parts as soon as I get some time and answers to the Y axis issues.

Dan

Thanks a lot for your reply and suggestions Glen. I did remove the resolver cover and cleaned it up with my contact cleaner. It did not resolve the problem. It sure would be nice to have a set of...

Thanks Glen. I'm going to check further on the Parameters. This problem seems to have just cropped up. I think there is a sheet with ladder diagrams, but I haven't seen any parameter sheets. There is...

Hi Group, Greg hope your checking these posts. I now have my machine working and I tried to program a simple program. Everything works, but now I find that the Y axis is actually doubling my input...

Thanks Greg,

I totally agree on the cleaning. I'm a clean freek myself and this unit is now out of the scrap yard and in my garage. (Picture attached.) You wouldn't believe how this machine looked...

Thanks for your reply and suggestions Greg,

My Mill and Keys were O.K. for about an hour this morning, then same problem. I slipped out and picked up a can of good contact cleaner and cleaned all...

Thank you so much for your interest Greg.

The only numbers I could readily see are: A61L-0001-0086 on the CRT itself and A86L-0001-0111 on the keypad. I have attached a photo of the control unit....

I have a Comet Mill with a Fanuc 10M system. I have an intermitent problem with the software key "Settings". ( second Key from the left). Sometimes I can use it and other times I can not get it to...

I am in need of the manufacture's manual for a 1985 Comet Milling Machine.

Model: Cnc-1630
S/N: 851633
System: Fanuc 10MA
Number: 5768
Manufactured 1985-10-23

I am willing to pay for...

After more research and fiddling I found that the Lead screw for the quill was rusted just enough to make it stick. I was able to free it up with a few taps with a dead blow hammer and some...

I just purchased a verticle mill with a Fanuc controller 10M. I have limited knowledge of this system. I powered it up yesterday and received an overcurrent alarm when I tried to Jog the Z axis. I...