Here's some pics of what I'm talking about. Item on the left is mis cut with the y axis off and with a tool change in between pocket cuts and thru cuts. The image on the right is correctly cut using...
Type: Posts; User: bwiab
Here's some pics of what I'm talking about. Item on the left is mis cut with the y axis off and with a tool change in between pocket cuts and thru cuts. The image on the right is correctly cut using...
I am losing my y axis after a tool change... before I learned about "save visable toolpaths to one file" in v carve, I would lose y and or x axis in between tool paths even with the same tool. Now...
Thanks routalot... that makes sense. A little bit of extra clean up doesn't bother me as much as my bit that exploded. I've been cutting with a whiteside 3/8" Compression bit. (HC4122).
the first...
Hello Peeps... thanks for all your help so far. I've been prototyping a couple of cabinets on my new Avid Pro 12060. I added a vacuum holddown using the Hurricane Vacuum. It works great. The first...
Well... I messed around with the tramming and got a 16" x 16" area pretty flat in both directions... then I went to surface the whole board. The area to the right of the red line is flat. The area...
Thanks. I will check it out but have been running into other problems with my machine today... :mad::drowning:
Hello... I have a Avid Pro 60120 and in the past 24 hours I've noticed a loud thump from the Y2 motor when I power on the NEMA 34 Control box... Not sure what is causing this but concerned that it...
Hello... So my auto z touch plate was working fine yesterday and today when I set the magnet on the collect it doesnt close the circuit. The touch plate still shows inactive in Mach 4. If I put the...
Doh... had it set to climb.... probably the source of my mistake... what do you think?
Hey there... Went to surface my spoilboard and noticed that the ridges of the cut will require some tramming adjustment. But what has me concerned is that the surfacing bit cut the first past...
Oh Man... I'm a moron... I have the Kent shoe... remove the magnetic part... duh! Thanks for the reminder.
I do have a 1/2" straight flute bit that projects 3/4" past the bottom of the shoe at...
Probably a minor inconvenience, but seems that using the touch plate with a dust shoe is a bit of a pain. Before attaching the dust collection shoe it was very easy to rotate the collet when using...
Thanks... my Z was set to max 0 and min -14
I thought maybe the safe height of 2" which was were the tool stopped after setting the start point for the work piece might be throwing it off......
I didn't notice this error before?
"Z Axis commanded over soft min"
what the heck did I do there?
Avid CNC (Inch) (*.txt)
Hello. Not sure if this is MACH 4 or operator error or something else??? I am working on cutting mounting slots for my Avid CNC and I created a test cut file with a single hole that I counter bore...
Thanks guys. Was planning on cutting either 1/2" mdf or 1" alder veneer mdf. The pattern copy I definitely noticed after studying the above images a little more... Not exactly what I'm looking for...
Hello - I'm fairly new to CNC. Just finished my build. Trying to layout a backsplash that is lots of custom and unique curves and spirals. I took a a stab at it in V-Carve pro and have access to...
Haven't watched the videos, but props on the ATC... that sounds like a dream.. :)
Hello Again.... hard to believe I joined this forum 7 years ago... Happy to report I just finished the build on a Avid CNC Pro. I got it moving but not quite cutting yet...
Well... turns out I had the y1 and the y2 sensors switched... doh! Thank you Avid!
Hello... just finished my assembly and I have the machine moving but can't seem to figure out homing... In mach 4 is "ref all home" replaced by "Home XYZ Axes"? my machine stops on the X but the...