Hello,
Have a TM-1 (2000 vintage) that we're trying to resurrect. Battery died. Lost marbles. Battery & marbles replaced.
X,Y,Z home and jog fine.
When I try to spin up the spindle, say 500...
Type: Posts; User: hrhoward
Hello,
Have a TM-1 (2000 vintage) that we're trying to resurrect. Battery died. Lost marbles. Battery & marbles replaced.
X,Y,Z home and jog fine.
When I try to spin up the spindle, say 500...
Hello,
We have acquired a TM-1 (2002 flavor) that has been in storage for a "little while". Battery died, lost it's marbles.
If I understand correctly, need to initialize. That will bring it...
Ok, I found the problem.
Somewhere along the line a few parameters got scrambled.
143 - DRAW BAR Z VEL CLMP: should be 250000, was 537120912.
222 - ROTARY AXIS INCRMNT: should be 0, was 134217728....
Hello,
We have been working on an older ('00) VF2 that has had some issues.
Got them all save one. If I initiate a tool change in MDI, M06Tblah blah, the Z goes to where it needs to, orients,...
Hello,
We have a Tsugami NP32C that had to have all parameters restored. What is the procedure for finding the physical Zero Return Positions on this machine?
Thanks,
H. Howard
Ended up being the SUB CPU.
Solved!
It was the servo amplifier. Go figure. Sent it out for repair and viola! It is working again.
-H.R. Howard
Hello,
The Z-Axis on a Mori MV-40E we have will not go up.
It will go down just fine. The brake is functioning correctly. It does go up a couple hundredths (using the hand-wheel) and I can...
Thanks deeps05,
I've tried every technique that I know of to no avail.
memoryman,
Which ones are the parity chips?
Alas, no difference. Thanks though.
Thanks for the reply tristarcnc,
Are you referring to these four chips? (in picture)
Hello folks,
Getting a 910 Parity Error (low) on power up. I have tried holding down Can & Delete, Reset & Delete, Reset & Can. Error message still there. Can't get past it.
Machine has been...
Hello,
Have a SL-25 that the NC will not power/boot up.
When the main is thrown on, the fans run, the drives go to stand by.
Push the NC go button and all of the membrane button led's flash one...
Hi mazak-user,
I appreciate your help.
[email protected]
Hello,
We just got in a Mazak Slant 15 1000 Universal w/ Mazatrol CAM T2 control.
When I push the control on button, the led lights up then goes out.
If I hold the button in the rapid, spindle,...
Sounds like a memory issue.
Thanks Machintek,
I have the disk on chip version.
Removed the mother and bmdc boards and cleaned the contacts.
Also moved the bmdc to another slot.
Voltage is 5.1, 12.08, -11.9, and 24.18....
Hello,
I have another EZ Path SD with no BMDC Desktop.
Been a little while since my last one No BMDC Desktop from 2006
I still have all the disks but I have forgotten which ones I need to load....
Best I can tell...
MMC CPU - 0 - Driver not loaded
NCK CPU - 2 - DRAM error on NCK CPU, defective during memory test after Power On
PLC CPU - steady red led - PLC in stop mode
Suggestions?
...
Hello,
I am trying to power up a HiT-18S with a Siemens 840.
Turn main power on, fans get to whirring. Push the power on button, nothing.
Here is a picture of what is going on inside the cabinet....
Thanks for the quick reply Al,
Don't know if it matters but I forgot to mention this,
It happens on both X & Y but not Z.
X-Y are controlled by the same axis controller. (A168B-2200-0200-05A)
Hello,
Have a Kiwa with the 0-M series.
The problem is this: From powerup to powerup it will not home to the same location. Usually about .200" off. As long as the control is not turned off, it...
What type is oil is recommended for the spindle on a VX-500?
Thanks
Yes it is. Thank you.
Hi. I have a Kia with a 0i-MB control.
Is there a way to display the total hours on the machine?
Searched but couldn't find anything.
Also, how do you set the date / time?
Thanks.
Got it up and going again. Turns out it was the back-plane.
Aaron at EMI worked with me to troubleshoot.
I also had to run what was on the disk labeled "Path_All_2.50.21_Install_Update, Disk 1...
Hello,
We have just got a Bridgeport Romi EZ Path S lathe.
On power up it gives me the message "No BMDC, Desktop"
I have checked CMOS. It is reporting the correct date and time even though it...
khaot183,
Yes, it did.
Just tried it a few moments ago.
Thanks, ad64075
ad64075,
Thank you. I will give that a shot.
The drawing calls it a
CMOS Hard Disk Emulator
Diversified Technology
No. CRR 804
How do I tell between version A & B?