501,555 active members
4,794 visitors online
Register for free
Login

Search:

Type: Posts; User: sabine

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Re: Double Arm Vertical alignment issue (Okuma Howa Millac 3VA)

    And the issue has been found. The crash actually did damage something - the cam roller bearing that actuates the internal atc arm that moves the sleeve up and down.

    Unfortunately I didn't find...
  2. Re: Double Arm Vertical alignment issue (Okuma Howa Millac 3VA)

    What you're looking at is the arm at the toolpot in the carousel not the spindle, sorry. I didn't make that clear. The soft Z did move, but since the toolpot is off but that much I don't want to...
  3. Double Arm Vertical alignment issue (Okuma Howa Millac 3VA)

    Hi all,

    I had a small crash earlier today. Nothing seems too wrong except the arm is now too low for the pot in the carousel. I've included a picture to show you what I mean. Is there a way to...
  4. Double Arm Vertical alignment issue (Okuma Howa Millac 3VA)

    Hi all,

    I had a small crash earlier today. Nothing seems too wrong except the arm is now too low for the pot in the carousel. I've included a picture of the ATC arm at the toolpot in the...
  5. Replies
    3
    Views
    141

    Re: Okuma Howa Millac 3VA spindle cooler out.

    Thank you much. I will definitely follow your advice.

    Yes, several things happened at once - my other machine blew up a motor drive and I had to move my shop.
  6. Replies
    3
    Views
    141

    Okuma Howa Millac 3VA spindle cooler out.

    Hey folks,

    I think the compressor died on my MAC oil cooler. At the moment I have little time and less money. It's pretty cold out...

    Has anyone run one of these without the oil cooler and if...
  7. Replies
    3
    Views
    264

    Re: Okuma Howa Millac 3VA Toolchange

    My bad, I didn't reset the operator message with an M02. Seems to work now.
  8. Replies
    3
    Views
    264

    Re: Okuma Howa Millac 3VA Toolchange

    Ok, I managed to get the ATC arm to move and removed the offending tool. Unfortunately, now the ATC arm doesn't move during a toolchange. Everything operates just fine until it's time for it to...
  9. Replies
    3
    Views
    264

    Re: Okuma Howa Millac 3VA Toolchange

    Ok, I managed to get it to make toolchanges. I still can't get the tool operations panel to actually set tool numbers, so I was going through and trying to retrieve the tools in the magazine...and...
  10. Replies
    3
    Views
    264

    Okuma Howa Millac 3VA Toolchange

    Hi all,

    I've been trying to get my Okuma Howa Millac 3VA working after sitting idle for some time. Everything seemed to be going well until I tried to do tool changes.

    The first problem: I...
  11. Thread: Position Error

    by sabine
    Replies
    2
    Views
    302

    Re: Position Error

    Thanks! I'll try these out today.
  12. Thread: Position Error

    by sabine
    Replies
    2
    Views
    302

    Position Error

    Hi All,

    I have a knee mill with a Centroid M400 control. I'm having an odd issue...I can do a rev/in adjustment and get the measurement perfect for any given distance, but the measurements will...
  13. Thread: RFQ

    by sabine
    Replies
    17
    Views
    2

    Re: RFQ

    Your inbox is full. PM me if you still need bidders.
  14. Re: RFQ: Steel washer/spacers 16x35x17mm qty 16

    PM sent
  15. Re: Small grinding (possibly turning job) in DFW

    For some reason I never got the PM Sending you one.
  16. Small grinding (possibly turning job) in DFW

    Hey guys.

    I don't have a surface grinder and a customer needs some hardened spacers ground down - they're 29mm diameter rounds varying from 1/4 to 1/8 of an in. Does anyone know anyone who...
  17. Re: Y - axis drive plate and NEMA 34 motor mount

    If you'd like you can share the project with me on Fusion360 for the quote. My email is william@sabinespeed.com, that should be how to find me.

    Thanks,
    William Brantingham
  18. Re: Autodesk Fusion G-Code EZPath II Post Processor

    Uh, basically what I meant by this is that if anyone has a G/M code list and alarm list for EZ Path IIs I'd love to have a copy.
  19. Autodesk Fusion G-Code EZPath II Post Processor

    Hi all,
    I'm developing a post processor for my EZPath II now that I've switched to Autodesk Fusion. The conversational control is okay, but sometimes I need a little more control on how the lathe...
  20. Re: Help we need to learn to run the EZ Path system

    Hey Bert,

    The manual actually has a programming tutorial in it. PM your addy and I'll send it to you.
  21. Re: Electrical connector - brass w/tin plate 2-3 sized qty 100ea

    Do you have a bigger picture? I'm having a hard time seeing the details.
  22. Thread: Tricket Bat RFQ

    by sabine
    Replies
    6
    Views
    2

    Re: Tricket Bat RFQ

    I'm interested in bidding, but yeah, like the others I'll need a .pdf or step file or similar. william@sabinespeed.com
  23. Replies
    2
    Views
    2

    Re: [RFQ] Small Steel Pins - Lathe Work

    I'm interested in bidding on this, but for a real quote I'm going to need some tolerances. I can give you a rough estimate if you like.

    william@sabinespeed.com if you'd just like to drop me the...
  24. Replies
    8
    Views
    2

    Re: RFQ 6061 T4 Aluminium Parts prototype

    PM sent
  25. Replies
    10
    Views
    4,945

    Re: EZ Path 2 manuals

    Sure do, but it looks like someone else got to you first, haha.
Results 1 to 25 of 57
Page 1 of 3 1 2 3