The machine comes with the ring. Place the ring on the lower head fully assembled. Make sure the ring is .002 below the table and run lntprdat program.
Type: Posts; User: sodickappsguy
The machine comes with the ring. Place the ring on the lower head fully assembled. Make sure the ring is .002 below the table and run lntprdat program.
make sure your cabinet is not getting to hot. The Qvic computers do not like to run hot. Also if you are networked make sure your machine are not running in the 192.168.200.XXX range. This will...
there is replacement computers that you can purchase from sodick.
if your fixture is rusting then your fixture it's becoming non conductive. If the fixture rest too much then power cannot flow through the fixture and burn the part properly. Check your resistivity...
is all 3 LED's lit up on both CPU boards? Did you check the 5 volt power supply and make sure it's working and doesn't have any AC running on it?
are you trying to do a manual wire Square and can't adjust the v-axis to align properly? have you tried to do an automatic wire Square?
clean the channel that the tank drain slides in. You may need to adjust the air cylinders that open and close the drains. take off the gray cover on the outside of the work tank on the right side. ...
Do you have power to the 386 and 86 cpu board? You should see leds lit on both boards.
i am afraid that even if you did take off all the sheet metal on top of the machine you would still be too high.
I usually go to basics and check power to the drives and make sure that if they are three phase drives that all three phase has power. Can you verify that the motors turn under power or does it...
The VZ series in the US will hold the 3-5 micron tolerance that you require. I am not sure of how they spec the machine in India but the US machines have a 4 cut generator without the Pika finish...
you will need to call up and get the factory parameter list and go through the set pages.
If the cables are cut clean there isnt much you can do. You can try and make some older heavy guage copper discharge wires but it will take several and for the money that it takes to build them it...
The High pressure flush wont turn on with T89 on. You can take the two brass knobs above the flow meters and turn them up and get alot more flow. You will have to back the power off also to keep...
i am not sure it can be done. Normally the B drive is reserved for a second floppy drive. I dont think you can change much in the software on a mark 25.
have you looked at your discharge cables?
if it is freezing over look at your exhaust water flow and see if it seems restricted. IF so try and reverse the water lines to see if flowing in reverse opens up the passage.
I dont have any schematics to send but i usually check at the connection at the motor and trace it back best i can. I would try swapping motors from X to Y if the wires look clean. You may have an...
Ric,
i would check to see if you have a broken wire. Also have you tried to swap motors to see if the problem stays with the axis. I saw in your pm that you did swap the servos and it stayed...
when you say it loops back up around the pulling wheels do you mean it curls up really bad and the wheel grabs it or does it never come off the roller? I havent paid any attention to the rollers on...
if you are getting .1-.2 ohms your cables are good. IF you just put the test leads together you will get that so you are close to infinity ohms. If you put the new leads on and the speed doesnt...
the SF is set for a maximum speed only. Sodick typically will set the SF higher than actual cut speed. What type of wire and Diameter are you using? Good flushing? Did you test the discharge...
Glad i could help you out.
Sorry for the delay. With the Thanksgiving holiday i have not been around my computer much. It seems like your already connected to the network so all you have to do from a computer in the shop is...
is your machine already networked but you want to use the remote monitor? I can help with the setup but i need to know some information. Is your network DCHP or static? Is it setup for Domain or...
people also use esprit, master cam and solidworks addins.
what LEDs? What i was told by another service tech is that the machine wont stay on if the floats are in the up position. On that style float (magnetic pickup style) if you take the floats off and...
Have you Cleaned the floats in the tank? If you took them off and cleaned the float take them back off and flip them over. If you havent cleaned them press them down by hand and clean them if they...
Look for wire that is caught in the ejection roller and the gears that drive it. Also make sure you dont have any broken wire around the upper head/theader assembly. If the wire grounds to the...
Make sure the fuse on the PSE-01 board isnt blown. is JP2 jumper on? I have never seen just the LED2 not stay on. I will ask around in the morning and see if someone else has seen it. From what i...