Search:

Sorry for the late reply.
I have quickly created something.
PGM only works with a 3mm ball cutter that was measured on the tip.
Row 15 and 16 give a Rz of 6,01


0 BEGIN PGM schr20rad15 MM ...

Of course you can mill that!
What tool did you wanted to use?

It's best to use a radial miller which you can use to run over the contour in X,Z.
After each run you can turn the coordinate...

I must bring the subject back again.....
It should now be a torus milling machine – not a ball milling cutter.

80mm diameter with no. 16 circular plates.
I still don’t know how I should face...

I’m a bit lost.
What exactly do you want to do?
Do you want to measure the position of the 2 red drill holes in relation to the pink drill hole?
Or do you mean the angle?

How do you call the tool change?

When I want to change my tool (manually), then I write L Z+300 FMAX M6.

Then the machine goes to Z+300 and waits until I have changed my tool and press ‘start’.

Hello.
I have a component with two radii. One inside R20 and one outside R18.
The component is clamped vertically at an angle. (Boring mill)
I want to mill these two radii with a D40 ball milling...

Hello guys
That may sound a bit weird now but I need some advice about drilling with a 3,5mm VHM Spibo.
I am working on a boring machine and the normal machine are more than 30mm plus.
We need...

Hello
I know it’s a bit short notice but I need to work on a component part this afternoon and I need a few hints regarding the strategy.

The tool is a HSS co D12 end mill 95mm long.


The...

Well on my screen the time is always visible. I don’t know why that is but I think it varies depending on the machine manufacturer.
Possibly the best would be to contact your manufacturer and ask...

Hello,

I have got a DXF file with hundreds of contour elements.
Now I'd like to convert these with CIMCO EDIT V5 in a milling program (engraving).
My question: is there any possibility to...

If I see that right, at No.1 of the Preset-table all axis are going to Zero.


ID 503 data of Preset-table
NR 1 Preset Number
ID x 1 axisA-W
=+0 data

I’ve got a counter question:
If the diameter above is 30mm and the diameter below has to be 45mm, how do you get at D45 below without destructing the D30 above?

Hello everybody

I’m looking for a manufacture (or several manufacturers) that would make a device shown in the attachment.
Could anybody help?

+1 or -1 declares only whether you want to mill in the same or opposite direction.



It declares the helical covering per circuit.
Similar to drill-milling (Q334=1.5; covering depth)

You can order the software for free directly at HH

http://www.heidenhain.com/

- Services and Documentation
- Documentation Portal
- CD-ROM/DVD

Hello
You can find all standard cycles in BHB by HH. But it’s also up to M204.

What is M306?

Do you work with label in your program?

Then it can be graphical discrepancy.

Otherwise automatic drawing shows mirroring correctly.

Stefan

Hello
We have the following problem: our machine thinks that a milling head (HUR 50) is mounted and wants to make an equipment change. We believe there’s a defect of sensors for detection.
So I’d...

We work a lot with Unidrill borer. You can drive it with full power.

I don’t understand.
Didn’t I help you? Or should I write the whole program for you?
How should I know what your G1/8 looks like?
It's not what you say, but how you say it.
You won’t find here a...

Metall
If I interpret your grammar correctly,

Security level = security space
Surface at = coordinates surface (where the thread begins)
Covering to = covering depth (how deep the thread should...

@Christian123

http://www.cnc-arena.de/forum/html/emoticons/thumbs-up.gif

@ CNCKrefeld

there’s an item in the tool table where you can describe the nose angle.
It has to work

I hope you won’t laugh at me… but what is an external tool?
If you describe the problem more exactly, someone will certainly help you.
;)

luftschraube

What controller is it for?

I’ve found something.
here you can input your formula and it will be reformulated.
Good luck

Stefan

What Czech barrel pickles turning lathe do you have?
TOS SUI?
I’ve worked with it. But without time loss during usage.

Stefan

Our controller has once been changed too. But completely.
The mechanic has read out the parameters from the old controller and then transferred them to the new one.

Stefan