584,829 active members*
4,984 visitors online*
Register for free
Login

Search:

Type: Posts; User: Beltdrive

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    687

    Re: Z0 after the tool change

    I like using format 2
    For tall parts or long tooling a typical program might go like this

    With Z fixture =0
    Tool 0s= surface to be drilled

    G0G90G80X-5.Y0E1 (Safe location to change tools)...
  2. Re: Axis amp replaced - now I get strange sound from axis motor

    I'm glad that I could help.
    I really like the fadals and I think the DC machines runs smoother than the later AC drives.

    I switch between 3 different A axis drives and reballancing the amp is...
  3. Re: Axis amp replaced - now I get strange sound from axis motor

    Do a Google search for "fadal axis ballance program "
    I found a pdf that has the factory service programs. You'll have to scroll through to find the one you need.
  4. Replies
    16
    Views
    1,925

    Re: Servo brake problem

    https://www.kmac-parts.com/product-category/amp-boards/

    I've used these guys recently as a month ago for a spindle encoder.
  5. Replies
    16
    Views
    1,925

    Re: Servo brake problem

    If the problem followed the amp to the y axis then I would change the amp.
  6. Replies
    16
    Views
    1,925

    Re: Servo brake problem

    I can't say for certain if the amps are the same between the X and A, the motors are different though.
    Under the cap on the servo motors is an encoder/resolver which are the same on DC drives.
    ...
  7. Replies
    16
    Views
    1,925

    Re: Servo brake problem

    I just looked in my 6030 and the A axis amp looks physically different but are wired the same.

    I take it that you are wanting to use the A axis amp so you can run the machine without using the...
  8. Replies
    16
    Views
    1,925

    Re: Servo brake problem

    We would normally switch x with y.

    Do you know if the machine has AC or DC drives?

    The ballance should be close enough to start the machine but will need to be fine tuned for accuracy.
  9. Replies
    16
    Views
    1,925

    Re: Servo brake problem

    Is this fixed yet?

    I agree that switching amps could isolate and help find the problem.

    You can switch the x and y motors the same way to see if the problem follows the part.

    It might be a...
  10. Replies
    3
    Views
    1,156

    Re: Screen Fading in and Out

    There are adjustment pots inside the pendant for brightness, screen size, contrast......
    I expect one of those are dirty or moving from machine vibrations.
  11. Re: Question about setting Z zero in part/fixture origin (G54, etc.)

    You guys must be lathe operators :)

    I work in a job shop where the tools change often.

    This system also works if the tools stay in tbe carasole from job to job.

    I set all tools to tbe...
  12. Replies
    1
    Views
    1,342

    Re: Subroutine move to previous position

    G0Z1.995G0X0Y0
    S3200
    F10.4
    M3
    G90
    G1G91Z-1.995
    G1G90X.46
    G1Y.75
    G1X0
    G0G91Z1
  13. Replies
    4
    Views
    6,166

    % O126 (PULL BRACKET) (MACHINE LEADWELL OMF)...

    %
    O126 (PULL BRACKET)
    (MACHINE LEADWELL OMF)
    (3 VISE MACHINING 2 PARTS PER VISE)
    (G54 X0 LEFT EDGE OF BACK JAW VISE 1)
    (G54 Y0 BACK EDGE OF MATERIAL VISE 1)
    (G54 Z0 TOP OF FIXED JAW VISE...
  14. Replies
    1
    Views
    1,268

    % O1000 (COMPENSATION-WEAR) (Post Rev 0.71)...

    %
    O1000
    (COMPENSATION-WEAR)
    (Post Rev 0.71)
    (FEB-01-2014-4:46:39PM)
  15. I might start by plugging the coolant pump into...

    I might start by plugging the coolant pump into the coolant 2 outlet to see if the problem follows.You will have to program m7 to turn it on.
  16. Shimming the spindle is not hard. Before...

    Shimming the spindle is not hard.
    Before loosening fasteners clean the area around the mount area well.
    If I can get within .0002 on 10 dia circle the blend will perfect on a 4 in cutter.

    4...
  17. Did you level the table or the y-axis ways? A...

    Did you level the table or the y-axis ways?

    A few year ago one of my machines was having the same problem. .010 drop in the y axis.
    First make sure all of the oilers are working. remove the way...
  18. My fadals baud rate is set to 9600 for...

    My fadals baud rate is set to 9600 for communications through the rs232 port.
    Jst yesterday a usb was installed on two machines. The baud rate is a higher setting Im not sure exactly what the...
  19. Which menu is not showing up? Go to setp and...

    Which menu is not showing up?

    Go to setp and check if the command menus are set to togggle with the space bar.
    Make sure the machine is home before going into the parameters.
  20. Thread: Fadal Quriks

    by Beltdrive
    Replies
    0
    Views
    698

    Fadal Quriks

    Hi guys,
    I am new here and did a quick search and dindt find any references to the G68 code.

    My shop has 3 fadals all with 4th axis.
    I have been running/programming a 6030 for 18 years now...
Results 1 to 20 of 20