584,837 active members*
5,567 visitors online*
Register for free
Login

Search:

Type: Posts; User: Leadshine

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    2,032

    Re: Red Light Flashing HBS86H

    How many times the red flashes in each cycle? if it is 7 times, it means position following error, indicating that there is a problem with the encoder feedback signal.
    Potential reasons?
    1. The...
  2. Re: MX3660 Estop Fault on two Drives, Over Current Fault on One

    Hello, according to my experience, this may be caused by the damage of the internal module?s?.
    Please contact your direct supplier to deal with or replace the module.
  3. Replies
    1
    Views
    2,906

    Re: wiring spindle to mx4660

    Hi Jacques, I replied your email before, as below...
    I checked your spindle DDBLDV 1.0 manual that it can be controlled by external analog input as motor speed control.


    However, its voltage 5V...
  4. Re: Leadshine technical support available on CNCzone.com

    Hello,Please let me know the model and serial number of your drive?
    CS series is designed for overseas customers so it's not released in China market there is no English manual and software on...
  5. Re: MX4660 with UC100 and UCCNC. Need help with output 1

    Hello, this is Jason Peng from Leadshine, It seems I had replied your this problem by email,please check. thanks.
  6. Re: Leadshine technical support available on CNCzone.com

    Hi Gantarone,
    For the control signal,there is strict time sequence to make sure the drive can recognize signal correctly. PS:Different drivers have different timing requirements
    Usually, the DIR...
  7. Re: Leadshine technical support available on CNCzone.com

    Hi Shane,
    Thank you for supporting Automation Direct.
    It seems that the drive DM860E does not receive the normal pulse/dir signal please check if there was any correct 5v pulse signal output from...
  8. Replies
    2
    Views
    1,270

    Re: CS-D508 closed loop stepper drive current

    Hi Luke,
    Thank you for supporting Leadshine products.
    The motor CS-M21708 is rated 2.5A, you need a tuning cable to set a smaller current in CS-D508 to avoid motor too hot.
    Please try to contact...
  9. Replies
    13
    Views
    3,189

    Re: Power Supply for HBS86H with Nema34

    Hi Digdagdigedag,
    Thank you for sharing us the experience on using Centroid controller and drive connection. Your comments are appropriate and reasonable.

    Actually, the logic signal current...
  10. Re: Leadshine LD5-400 DC Servo Drive not working in jog run mode

    Hi ManjuHBR, thank you for supporting Leadshine products.
    The motor phase UVW must be corrected to the drive LD5, do you have motor datasheet and where did you buy the low voltage servo drive...
  11. Replies
    13
    Views
    3,189

    Re: Power Supply for HBS86H with Nema34

    Hi Digdagdigedag, thank you for helping us.
    YES, we need to know how LMEB83 connects this 12v power supply signal as a pulse/direction signal input. It is likely that the single-ended signal input...
  12. Replies
    13
    Views
    3,189

    Re: Power Supply for HBS86H with Nema34

    How do you connect this 12V to the pulse and direction signal? whether there is correct pulse signal output to the drive.
  13. Replies
    28
    Views
    11,301

    Re: MX4660 Speed Control for 2.2 KW huanyang vfd

    The MX4660 schematic is not released, there is a channel to output analog signal to control VFD. Refer to page19 http://www.leadshine.com/UploadFile/Down/MX4660d_V1.2.pdf
    PIN14 for PWM on DB25,...
  14. Re: Leadshine ES-DH1208 faults wtih ER020 frequently

    First of all, I'd like to know what model of new motor you have changed? If you have used Leadshine encoder extension cable ? I think there are some problem with encoder signal transmiting between...
  15. Re: Leadshine ES-DH1208 faults wtih ER020 frequently

    Hi Ron,
    Thank you for your attention on Leadshine products.
    Err020 means position following error. Our default setting is 1000 pulses in the software. If the error value of encoder feedback exceeds...
  16. Replies
    1
    Views
    920

    Re: Dm 320C Drivers

    Hi,Garry
    I am John ,an application engineer from Leadshine.
    Can you send me your wiring diagram of DM320C to Breakout board ?
    Actually ,there are many factors cause the drive not working.from...
  17. Replies
    8
    Views
    2,412

    Re: MX4660 VFD Speed Control Issue

    Hi
    This is a common issue for MX3660 AND MX4660 , the IC has 1.1V oltage drop ,so that the output is not 10VDC
    I am sorry for that ,and we don't have solution for that .

    John
    Leashine
  18. Replies
    1
    Views
    856

    Re: Lead shine easy servo systems on eBay

    Hello
    Both ES-D /ES-M and HBS/HBM are from Leadshine . but ES-D /ES-M is special for oversea market .HBS for domestic market .
    Some Chinese trading company sell HBS too .but no technical support...
  19. Replies
    5
    Views
    1,937

    Re: LeadShine drivers recommendtion

    Do you mean something for stall sensing of drive ?
  20. Replies
    16
    Views
    5,435

    Re: MX4660 Power questions

    I don't know how to attach the files here .but if anybody want this file , please email me directly .
    [email protected]


    John
    Application engineer
    Leadshine
  21. Replies
    16
    Views
    5,435

    Re: MX4660 Power questions

    I am JOHN ,an application engineer from Leadshine
    We have a document special for shunt regulator and capacitor information .
    Would you mind telling your email , i can email you this document

    ...
  22. Replies
    5
    Views
    1,937

    Re: LeadShine drivers recommendtion

    Dear Sir
    Thanks for you would like to use Leadshine products !
    Base on your motor information , i recommend you to use Leadshine DM870 or DMA860H.the below link is DM870 details
    Leadshine...
  23. Re: Leadshine drivers current settings Peak / RMS vs motor rated A

    Hi Kmin
    The peak current =1.3*RMS ,normally ,we set RMS for the motor
    For your motor 1 ,PK299-E4.5A ,and if the connection type is parallel ,the current setting on DM860 should be 6.00A -----...
  24. Replies
    1
    Views
    869

    Re: MX3660 Touch Plate Question

    Hi Donny
    I have replied your email .


    John
    Application engineer
    Leadshine
  25. Replies
    2
    Views
    3,140

    Re: DM542? Discontinued?

    Hi
    DM542 is not Discontinued,but we have not released it on our website ,you can buy it from leadshine directly or leadhsine distributor .
    Are you in USA ? if so ,you can buy from Leadshine...
  26. Replies
    2
    Views
    958

    Re: Pulse width for DM856

    Hi
    For DM856 ,the Max input pulse frequency is 200Khz .
    You can set the Kernel speed just base on your machine working speed and the micro step setting .
  27. Re: Can I add a 4th axis when useing a Leadshine MX3660

    Hi
    Please read the user manual Figure 18 ,MX3660 connection diagram .
    There is diagram for 4th aixs .
  28. Re: Can I add a 4th axis when useing a Leadshine MX3660

    Hi
    It is possible to add one axis on MX3660 ,but this axis is different from other axes ,the speed is limit .the Max output pulse frequency is about 20Khz.
    You can download the updated user...
  29. Replies
    2
    Views
    1,649

    Re: Leadshine Pro Tuner serial port settings?

    Hi
    No need set the serial port configuration settings ,the default is ok .
    PLease send me some screenshots ,let me check it
  30. Thread: MX4660 kit

    by Leadshine
    Replies
    13
    Views
    3,525

    Re: MX4660 kit

    Hi Bryan
    The DB25 cable is standard parallel cable for printer , i think you can find it from your market .
    286032
    The cable for motor is not necessary to buy a shielded cable ,the normal one is...
Results 1 to 30 of 38
Page 1 of 2 1 2