Search:

I had my own part time business. I did Okay; what you say about everyone wanting the cheapest price is all too true so you can imagine my surprise at how much money they were throwing at my son the...

Surjit

I am not really sure what it is your are asking, but if it is the software to run your control I don't have it for a mark 25. Sorry I couldn't be of much more help.

I am trying to grease the ways and lead screws on my Mitsubishi DWC 90G and I am unable to find a way to do it. There are no grease fittings with which to apply grease where it is needed. There must...

Hello sodickappsguy. I was reading the instructions on that taper program you posted. When you say the head will go down I assume this program is for an automatic Z axis machine. Is that correct?...

Hello Royster

I had tried to get out of the bounce with your suggestion weather I followed your method exactly or not, we aren't talking exact controls it didn't work. However today when it...

First You should have started a new thread. You are stepping on MidWest here and his thread.

Look to see if there aren't any discs with software that need to be installed first. They may be what...

Sodickappsguy Thank you for your advise.

Thanks for the information. One more question. Is using Zinc coated wire harder on the equipment, and if so, how then?

I am cutting stacked Alum. pieces on my Sodick A 320 D. What kind of wire would I get for the best results ?

Getting started like this is rough. First hard lesson I learned was to ALWAYS write down your MACHINE POSITION! after you have set up and are ready to cut. With that you can always go back to the...

Called up tech support from the Sodick web page. Few minutes on hold they answered. Much like you said. A complete shut down and reboot of the software. Just a few minutes later I was underway again.

I am running a SODICK A320D with a FINE SODICK EX21 power supply

I hit the red all stop button last night as I do when nothing is running in the machine. When I came in I prepared to do a wire...

Thanks. Hard lesson learned as I am only getting back into Wire EDM after being away from it for over 20 yrs. I lost my start position and may have ruined my piece. From now on, I am writing down my...

Where would I find my resistivity sensor on my Mitsubishi DWC 90 G so that I can clean it ?

Mitsubishi DWC 90 G is the one it happened on.

Yes I believe it is. Talk to Sunnen.

In a "drill press" it is referred to as Lapping basically the same type of metal removal just not as accurate. A lot of guess work as to when it's finished. Getting it honed with a honing machine...

Running a job;the wire runs out and I go to re-lace it. I come to find the head line up is halfway between the start and the last point of contact (straight cut). No obstructions to short it out in...

Glad for you. Some proof this site works.

How much material are you removing ? Honing might be the way to do this.

I know there is a procedure you follow when rebooting the software into the power control unit. I don't have it in front of me now (home) but if you have the manuals you may find it in there under...

I can't give you a solid answer but given your situation I would look into Panasonic. They would be able to help you best with the boards.

Having used ShopCam I find it is easy, clean, and simple. I haven't used it to do a lot of complex shapes but for the price it is a bargain. Support is excellent. However you will have to talk to...

Thanks. The wire broke because of "I don't know why" reasons. Plenty of wire on the spool However being relative new on this machine can you explain how I proceed as you suggested. The guy I had...

I broke the wire on a cut. Now when I return just short of the cut location using "PLOT" and continue with machining it will advance and hit the work and bounce off and continue to do so until I shut...

It depends on what your cleaning. A safe bet is to use jewelry cleaner.

I call these people crying climate change "Modern Day Carpetbaggers & Scalawags" I perceive them no differently then Gypsies pan handling snake oil to enrich themselves.