Hello,
Have had the sinker as per title for several years, its now alive, serviced, filters, Dielectric and tooled.
Need training but before i book this I feel the need to have a little knowledge...
Type: Posts; User: mossy123
Hello,
Have had the sinker as per title for several years, its now alive, serviced, filters, Dielectric and tooled.
Need training but before i book this I feel the need to have a little knowledge...
Hi Guys,
i have a Huron MU6 on Heidenhain TNC360, 1996.
shut down ok and now on restart when i press the button to pass over ref points it flags up - X AXIS OVERTRAVEL without the machine...
Keith,
Error 20 is overtolerance of rad in G02-G03.
distance between start point and ctr of arc and arc to end point exceeded value in Parameter 876.
Chris.
Hi Keith,
I also have a W0.
For the feed as you have been (G95) servo feed but you can control with constant feed G94 F120. F being the feed rate of 1.2mm/min.
F0.6 would be 0.6mm/min.
Over...
Hello Gert,
Sorry for the slip-up, was in a tremendous rush earlier.
it would seam you have all you need but please find below the correct data pages under load just in case you need to cross...
Gert,
There is no unstable lines on any page whilest cutting or not!
Chris.
Diagnosis pages whilest not under load:
Hi Gert,
Diagnosis readings while cutting:
Chris.
Hi Gert,
Yes I will do this for you but will be a couple of days until I cut again if you can live with that?
Gert, what does this diagnosis page mean, where is there reference to application...
Hi Gert,
please look back at my thread as i have just wrongly posted a reply to help you there with a picture.
Kind Regards,
Chris.
Hi Gert,
took picture anyhow as wont be able to once im burning again in 1/2hr with some luck.
Kind Regards,
Chris.
Hi Gert,
you fixed it.
front splash guard interlock switch.
would never have thought as i had noticed even when not depressed / guard not on correct all works!
must be a faulty switch as EDM...
Hi Guys can you help?
Fanuc W0 wire eroder.
I'm new to this and the machine has been going good for a few weeks before training i need for taper cuts.
overnight burn last night, 12hrs, 86mm...
Hi Gert,
Just sent you a private message then seen your pictures.
the blown item is turquoise in colour as with many.
look at bottom of board.
2 vertical black heat sinks, to the left of...
Hi,
Been away so just got your post and had word back from my people regarding back up and availability.
we seem to be failing so what i have here is now very precious.
i will back up all i have...
I'm new here and to EDM but have you allocated any offsets and technology? has the program read this yet? is there anything set under the cutting conditions number you have assigned in the program?...
That would make sense Medm as i know that the rapid oxidisation is the reason for use of AC whilest tig welding though i would never have thought to apply this to EDM!
Little snippets like that are...
Hi,
you sound like you will always be OK as driven and not perturbed by diversification.
was expecting there to have been terminal problems with boards and drives so with being earlier machines...
I bought W0 manuals and Technology earlier this year from fanuc new. they were very helpfull but warned me from the start that there is around a 12 week wait as no stock and print to order on these...
Good Morning,
Thank you for the advise i will try what you are telling me.
we are well supported over here, parts and help all on tap. good machines can be found at EDM services for one and...
Hi,
my machine is 1991 and very clean, very lucky to find it and cheep but as with everything the tooling and setup has cost me spread over 14 months of picking up pieces.
i have just looked...
Hello.
OK then, several passes with different offsets!
i can manage that and have done.
i have been altering the off time manually as cutting.
its knowing how to set the technology and tell...
Thank you for the fast response.
My W0 has auto for EDM settings.
if i am to sellect:
SKD11
16mm thick
0.25mm wire
the following settings are thrown up:
Hello All,
Im new to EDM and struggling a little:
Fanuc W0 tape cut, non submerged.
my question as i cant find answers anywhere else is: