584,858 active members*
4,375 visitors online*
Register for free
Login

Search:

Type: Posts; User: metlshpr

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    830

    LOOKING FOR A NEW BACK SPOT FACE SYSTEM

    So we have been using the Widia back spot face system for years. Now they are discontinued. recommendations on what to go to?
  2. Replies
    4
    Views
    1,100

    Re: 1 1/2 internal npt thread

    All info can be found in the machinist handbook for the major and minor sizes. The above attachment information was gathered from there.
  3. Replies
    4
    Views
    1,100

    Re: 1 1/2 internal npt thread

    https://www.cnczone.com/forums/attachment.php?attachmentid=405510&stc=1
  4. Re: NEED TO PROBE A BORE WITH MORE THAN 4 POINTS WITH RENISHAW PROBE

    Could you please show me an example of the written code?
  5. NEED TO PROBE A BORE WITH MORE THAN 4 POINTS WITH RENISHAW PROBE

    I would like to be able to probe a bore that is egged to find the average center of the bore. The issue is that I cant find a probing cycle that will allow more that 4 points. Is there any help out...
  6. NEED TO PROBE A BORE WITH MORE THAN 4 POINTS WITH RENISHAW PROBE

    I would like to be able to probe a bore that is egged to find the average center of the bore. The issue is that I cant find a probing cycle that will allow more that 4 points. Is there any help out...
  7. NEED TO PROBE BORE WITH MORE THAN 4 POINTS WITH RENISHAW PROBE

    I would like to be able to probe a bore that is egged to find the average center of the bore. The issue is that I cant find a probing cycle that will allow more that 4 points. Is there any help out...
  8. WANT TO PROBE BORE WITH MORE THAT 4 POINTS WITH RENINSHAW PROBE

    I would like to be able to probe a bore that is egged to find the average center of the bore. The issue is that I cant find a probing cycle that will allow more that 4 points. Is there any help out...
  9. Replies
    3
    Views
    1,241

    Re: CODE TO USE LASER TOOL SETTER ON HM 8000

    Renishaw Its a NC4 non contact. I did find the code from a friend that has a hm400 with the same control (M50 B1.0). And I got Renishaw on the phone for the procedure to clean the lens. I was getting...
  10. Replies
    3
    Views
    1,241

    CODE TO USE LASER TOOL SETTER ON HM 8000

    I have started at a new shop as the supervisor and they have a HM 8000 with fanuc 31i-model a. The guys here have told me that the tool setter doesn't because of soft ware missing. Well, sorry but I...
  11. Re: Looking for HAAS VMC Visual Quick Code (VQC) Template File

    I know this is an old thread but I have a 2012 VF-4 and need to load the VQC on it. Will this file work and if so how do I load it?
  12. Sorry I got the machine wrong in the title but...

    Sorry I got the machine wrong in the title but correct in the post. It is a DT2550.
  13. Sorry I got the machine wrong in the title but...

    Sorry I got the machine wrong in the title but correct in the post. It is a DT2550.
  14. Mori DT2500 tool presetter might need to be turned on

    I have a Mori DT2550 with Fanuc MSX- 504 IV control that I have had the presetter replaced. The issue is that I will put presetter in machine and normally the control on all my other Mori machines...
  15. Mori DT2500 tool presetter might need to be turned on

    I have a Mori DT2550 with Fanuc MSX- 504 IV control that I have had the presetter replaced. The issue is that I will put presetter in machine and normally the control on all my other Mori machines...
  16. Just wanted to let you all know that we think we...

    Just wanted to let you all know that we think we found the issue. It seems that the main breaker is bad. The machine will trip and we can push the switch in the on direction and it will run for as...
  17. I'm Mike's supervisor here and I would like to...

    I'm Mike's supervisor here and I would like to give out some more information on what has been going on here. The troubles with this machine started at the end of this summer with what was called at...
  18. Thread: mastercam X5

    by metlshpr
    Replies
    3
    Views
    580

    If you have the casting modeled, you should be...

    If you have the casting modeled, you should be able to set that as your stock.
  19. Replies
    7
    Views
    1,376

    Do you have 4th axis capabilities? That would...

    Do you have 4th axis capabilities? That would take care of the distortion.
  20. Replies
    7
    Views
    1,376

    do a 2d tool path and then use a surface project...

    do a 2d tool path and then use a surface project tool path onto the sphere
  21. Thread: 4th axis noob

    by metlshpr
    Replies
    6
    Views
    863

    First of all. I don't understand why there is z...

    First of all. I don't understand why there is z moves in the code thruout?????
    Seconed. the other file you attached is a DWG not a MCX-5, so I can't be sure of what you are doing wrong.
    I'm at home...
  22. Thread: 4th axis noob

    by metlshpr
    Replies
    6
    Views
    863

    this is just a simple contour path where i made a...

    this is just a simple contour path where i made a 3axis rotation about z. the lead in and out will be with the rotation that is the nature of this beast. that is so there is no tooling mark at the...
  23. Thread: 4th axis noob

    by metlshpr
    Replies
    6
    Views
    863

    here you go

    here you go
  24. Replies
    8
    Views
    1,289

    I try!

    I try!
  25. Replies
    5
    Views
    909

    *

    *
  26. Replies
    6
    Views
    1,165

    AS cadcam said, if the walls are straight then a...

    AS cadcam said, if the walls are straight then a 2d path should work just fine. With you saying that it is a mold a naturally assumed that the walls are tapered. But I'm glad you are happy with the...
  27. Replies
    6
    Views
    1,165

    I would do a surface finish contour for the walls...

    I would do a surface finish contour for the walls and then do the scallop for the floors.
  28. Replies
    1
    Views
    780

    You will have to be more specific. Or you can...

    You will have to be more specific. Or you can post the file.
  29. Use tool path transform, enter parameters and hit...

    Use tool path transform, enter parameters and hit go.
  30. Replies
    10
    Views
    2,748

    Here it is.:banana:

    Here it is.:banana:
Results 1 to 30 of 120
Page 1 of 4 1 2 3 4