Search:

Hi,
I want to buy a power chuck for a 1997 Okuma LNC-10 L1420 Cadet Turning center. Does anyone know if a A2-8 mount is compatible? Currently I have a collet chuck on it.
Thanks for any help.

Yes, that is exactly what I mean.
Thanks.

Hi guys,
I am looking at adding machines possibly with fanuc controllers. I currently have a Robodrill with a Fanuc 16 I believe. To my knowledge the fanuc 16 will not perform local subroutines. ...

Thanks,
Also I was wondering about the spindle bore. Says it has a spindle bore of 3.9" but only a bar size of 2.44". Is this due to the hole size of an 8" chuck? Is it possible to get to a bigger...

Hi Okuma experts. I am looking at a used Okuma LR15, it has the front and rear turrets on it. It doesn't have a tail stock but I was wondering if it is possible to use one of the turrets as a tail...

I do have graphics.
Ok, I thought it might be something with machine lock or dry run but when I try to select those buttons the interlock button flashes on. I have also tried this with the key in...

Looking for help on how to verify a program made by my cam system on my Okuma LNC 8 lathe with osp5020 control.

Thanks

What is the best way to set the height offset on this control? Seems the only way is to have to type in the values but is there an automatic way to do it?

I changed the post to add 20 to the diameter offsett from D09 to D29 is what I meant.
But now I am starting to understand. I have just been used to having a seperate menu for diameter offsets in...

My offset screen appears to me to just show the length offsets
243622
Is there another screen?

I have my cam program to add 20 to the diameter offset like your saying. But as far as the...

Yea, I see what your saying and I am still trying to tweak the post processor but that doesn't explain the problem I am having. Its almost seems like there is a huge compensation value entered in. ...

So I just got the robodrill. It is from 1995 and has a fanuc 16m control.
I am using cam to make my programs and the machine isn't working correctly when it has a cutter comp programmed.
Here is...

Looking at buying Fanuc Robodrill a-T-10b with fanuc 16-m controller from 1995. Any knowledge on this would be appreciated but I am mostly concerned about the amount of control memory it might have...

Where do I find the spindle speed clamp?

We are having this same exact issue. It does it on both our haas and okuma. Anyone know how to control this in the UPG software?

235162

Thanks
Other than being on the B: drive that worked.

I over filled the memory on my VM16 with centurion 6 control and it shut down and will only go into dos mode. Does anyone know the DOS Commands so that I can get to the parts directory and delete...

Damn that feed per rev.!
You were right again.
Thanks
Jake

Ok that works to reset it. It starts to run again but then it just stops when it hits this line:
G01X2.2 G42 F.008
Z-.06 F.007
Any thoughts?

Hi,
I have a simple program that faces off, cuts to diameter, parts off, and uses a bar puller to position the stock for the next cycle. I want to just loop this for say 5-10 times so that it can...

How can I find out if my control contains drip feed?

I did find the IGF parmeter for enabling the bar puller but I haven't figured out where in IGF to program it so I was just triing to enter in...

My hybrid programming for the bar pulling I want to do is:
following the IGF line of code of N306 M05 M09
with the spindle stopped I need T0606 (a bar puller) to cross feed in,
so I have a - G01...

Hi all,
I am a high school machine shop instructor and we recently acquired a 1993 LNC 8 turning center with OSP 5020L. Slowly figuring things out but have some questions.

1. It has an rs-232...

Excelent points,thats what I am after. Actually I am very interested in an okuma like that. Most similar to what you showed me the dealers are asking $25,000 or more for that. Just having a hard...

Just checking, did you look at the link?

Thinking about buying a 1983 Mori Seiki SL-B Turning Center for a High School Machine Shop that I teach in. Seems to be in nice condition and seller would take 10,000 for it. Thinking maybe about a...

Probably going to use my vmc to machine it because there are some threaded holes around the outside. The square hole does go all the way through so a broach may work. I must admit that i am not...

So have a broach made? Can I broach something like that in a VMC?

Hi, need help/advice in how to machine a small, deep, square hole in Stainless Steel.
The hole goes .600" deep and it is .132 wide and has a .093 radius on the ends. I attached a pdf. for you to...

I would say your problem lies in the cable or computer. You probably have, but I would double check the wiring of the cable. If thats a 100% than its gotta be the computer. There could be some...