Hi guys,
I'm using Mach3 and Sheetcam and my rapids are way slower than when I move manually with arrow + shift. Since my arrow- shift speed is fine I guess my motor tuning is ok and it must be a...
Type: Posts; User: Lama2
Hi guys,
I'm using Mach3 and Sheetcam and my rapids are way slower than when I move manually with arrow + shift. Since my arrow- shift speed is fine I guess my motor tuning is ok and it must be a...
Thanks a lot.
I bought my whole router ready assembled with spindle and VFD installed. Has been working properly for over a year now so connections should be fine.
But ok then my question is...
Thanx Al, very clear. I guess I need to find out how many poles my spindle has? Or is that usually 2 poles for a typical 3KW spindle?
What would be the formula for more poles?
Hi there,
I started working more with aluminum recently and want to get feeds and speeds mu ch better. I found a good online feed and speed calculator but I don't know how to apply it to my VFD and...
Hi guys, thanx for your advise.
How stupid can I be. If been using this additive in my manual mil for years. But in the enthusiasm of getting my CNC started I just forgot about it.
I guess the...
Hi,
The cooling water of my 2,2 Kw spindle is turning dirty brown rather quick. I've been using plane water and the spindle is made in China. Should i use any additive to avoid rust? Or is this...
Similar question about holes in topple:
I want to make a vacuumtable and found the model of DONEK on you tube with a simple vacuum cleaner and a topplate with holes
...
Problem solved in the meantime thanx to a Les from Sheetcam:
Check under Options->machine->machine type , check if the 'drag knife' option is selected.
it wasn't ..
Thanx Les
Hello,
I purchased a Sheetcam license with a dragknife option and was able to use it for some hours. Then after importing a new file (that was probably scaled too small) I tried to create the...
Thanx a lot Gerry, problem solved
Dear aargh,
I finally had some time to follow your suggestion. Actually there were already some plastic (HDPE ?) strips glued on the table. So the machine is probably designed with the idea to...
Thanks for your reply.
I will check more thoroughly if it is repeating exactly.
Will also check if it may be the T slot profiles that may be mounted badly or deformed. They are aluminium, which...
Hello,
I bought a mill with a 130 x 250 cm table with T slot rails.
I found out the bed is not 100 % flat. There's a max difference of 1,8 mm.
I want to cut large pieces of paper with a Donek...
Hello,
I just wanted to point out that I simply had the wrong plugin. The seller had insisted I should install the plugin for another controller (Xilifeng Mach3 USB motion card'). They were...
Hi Jeff,
In Device manager it s clearly there
In the task manager I'm not sure what I should be looking for.
Here are some screenshots.
I was wondering if you could be bothered to log in to my...
Hi Jeff,
Am I right that you have the same USB controller card?
Could you send me a screenshot of your port settings?
Can the problem be caused by in or outputs wrongly connected to the USB card....
Jeff,
Unfortunately that didn't help neither
I find the term 'External motion' rather strange though. Is it really about the motion controller?
And how where you able to provoke the message on...
Hi Jeff,
Just tried another cable but no luck.
With RMAd I guess you mean return to sender for replacement? And wait a months or 2!
No other suggestions?
Best
Lawrence
Hi Jeff,
Sorry, seems like your reply only appeared just now, must have overlooked it.
Anyway: it is Mach 3 Version R3.043.066 Just like in your image.
I see you are able to recreate the same...
Hi Jeff,
I downloaded the plugin (last week) from the Leadboy77 site (as instructed by SaleCNC, the supplier of the machine and controller)
see: Leafboy77 - Home
Scroll down +/- 1 page till...
Hi Jeff, Thanx again.
I followed your instructions on making a new folder and the 'Xulifeng motion' does appear under configurations. (see image)
Yet the message 'External movement not...
Hi Jeff, Gerry,
Thanx again for your help
But no flagged devices. (see images)
I double checked if the USB cable was in the right USBport, and it is in port 1 hub 4 with the message: this...
Yes I did and as far as I know there is only one plugin folder?
Here's an image of the plugin folder
278744
My former reply was maybe not so precise: when i 'reset device selection' i get the message:
'you will be asked on next start up what device to use if plugins are available.'
Yet after restarting...
Thanks for your reply!
I did this (earlier and now again) yet the same problem remains.
I wonder If my port settings are correct under config? First I had Port 1 (0x378), which s I believe the...
Hello,
I just bought a Chinese 4 axis CNC mill from SaleCNC. I seem to have a problem with the communication between Mach3 and the USB motion card controller provided by Sale CNC.
I followed...