Search:

Hi, the post processor will produce an *.iso file that will need to be loaded to the machine through the WRT, program editor and not Biesseworks.

Hi, can you add a picture of the label being produced.

Do you have automatic labelling (on the loading table) or manual labelling (at the offload).

Hi, I've sent you some information.

On the machine you need to make sure that the milling depths are only just into the spoilboard (normally 0.2mm) the spoilboard needs to be from MDF with a...

OK, I've asked the forum help to look at my PM settings.
Do you create the programs and nests at the machine or in the office?

Hi,

Are you using BiesseWorks or the older Blue Editor?

I think your machine should have BiesseWorks, but maybe you are using 3rd party software in the office and so use the blue editor on the...

Hi, I'll send you some more info (with pictures) later, where are you?
Can you PM an e-mail address to me?

Have you tried to onion skin (two pass) cut your nests?

In routing instruction set vertical passes = 2 and final pass = 1
In optimiser data tick "through machining at end"

Hope that helps.

Hi,

Those pins are for the sensors in the spindle that sense whether the tool is installed (locked) into the spindle.

Do you have a picture of the name plate of the spindle?

Hi,

The spindle will be made by HSD, maybe if you search for that you may find something.

I think all controlon Biesse machines is 24Vdc for solenoids, but there are no solenoids inside the...

Hi,

How old is your machine?
What software are you using on it?
What materials are you machining?

Cutting in one pass depends on many things, size of your pieces, material, level of vacuum,...

Hi, Have you talked to BiesseUK about the software?

They could help, even upgrade your machine to the newer bSolid software now being shipped with their machines.

What problems do you have with the original software supplied with the machine?

Or the tool diameter is correct, but compensation has not been set/used.

Well, I've added you both as contacts, so hopefully that will help out.

Well, I've checked all my settings and I cannot see a reason for the error you received.

Did you send me a msg. with an e-mail address?

Are you still struggling with BiesseWorks and Macros?

Hi,

How have you disabled the mats?
If you have bridged the cables going into the mats (and you have done that correctly) you may have a faulty mat control module.

Your machine has a gantry, can you move it by hand, when you do, can you feel a slight knock when you start/stop.
Then try the same when moving the head on the gantry.

When you identify where the...

Check the backlash in your X and Y axis drives.

I've worked on older cnc routers with large drilling units that use standard air cylinders, adjust the air pressure to suit the weight. Newer machines have just the motor and ball screw.

Hi, if you connect the PC to the internet and get Biesse to dial in they will be able to pinpoint the problem very quickly for you. In the UK this would be a free service, so it has got to be worth a...

Hi,
Are you sure everything is connected correctly to the PC?
Have you checked that you have all your voltages (400V L1-L2, 400V L2-L3, 400V L1-L3, 24V dc) in the cabinet, no circuit breakers...

I was once warned that automotive coolant has additives in it to prevent leaks, these can cause problems when used in systems with small csa circuits.

Hi,
If you could take screenshot of the error messages (expand the window to get them all in) and post it on here it might help.
At the moment, don't worry about the white light, nothing will work...

Did you see it running before it was delivered to you?
It sounds as though there is a connection issue, are you sure everything was re-connected correctly during the install?

Artic Flu -5

They supply the UK, but do not manufacture in the UK.

It is a good system, even Hypertherm use the Esprit machines in the European Tech centre.

The gas usage will depend on the materials and thickness's you want to cut, I'd recommend the autogas over...

What software are you using?

Hi,

OK, I'll see if I have anything that could help you, drop me a PM with your e-mail address and I can forward you some documentation.