506,621 active members
4,017 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Re: Haas mill and lathe overvolt power problems

    Your first thoughts where right they must of been shut down too long it pays to power them up every 2 weeks just run them through a cycle spindle warm up Etc and leave them on for a few hours, they...
  2. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    You are able to change the speeds in any mode be cause you are not using any of the drive defaults

    With using the KeyPad only

    Jumper J1 would be in 2-4 position I think this is the part you...
  3. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    You GFCI is not a switch for turning something On / Off with, it is a safety device, a regular switch at the wall is fine, Plugging a VFD Drive into a live Plug that can cause a spike and take out...
  4. Re: Haas mill and lathe overvolt power problems

    Call Haas some of the service Tec's may have an Idea of what is happening , have you tried to clear the alarm with ReSet button
  5. Re: Fault F-602 in Yaskawa 626VM3C servo drive.

    He most likely put it in manual mode ( KeyPad Control ) for testing, I hope he did not do a ReSet if he has you would of lost all the Drive Parameters
  6. Replies
    8
    Views
    24

    Re: spindle speed not changing

    PD144=3000 not 2000 this should get you to your spindle max 18,000RPM with KeyPad control

    If you are getting a PWM errors then you need to look at your wiring there could be a problem how you have...
  7. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    The manual states very clearly PD003 is the Main Frequency, and needs to be set at the max Frequency that is being used

    What is the reason for this, if there is a power cut the only Parameter...
  8. Replies
    6
    Views
    10

    Re: 6040 X axis strengthening again.

    A plate on both sides as from your photo would do much the same thing, you may have to step the plates out to get clearance for the Z axes slide a thicker back plate would help some rigidity but...
  9. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    I'm afraid your VFD Drive is no different from what anyone else's has, here is how the KeyPad works and needs to be set to memorize the last speed

    You are making it sound like it is different...
  10. Replies
    8
    Views
    24

    Re: spindle speed not changing

    Mach3 can be tricky to get right which seems to be where your problem is, if you have no voltage change then something in the Ports and Pins may need to be changed

    All your basic settings look ok...
  11. Thread: Flat V-Bits

    by mactec54
    Replies
    2
    Views
    3

    Re: Flat V-Bits

    You can not measure a D-Bit angle like that there is only ( 1 ) edge that will be correct

    Only one edge will be the cutting angle so off the shank and the angled cutting edge is what the angle...
  12. Replies
    25
    Views
    40

    Re: 30x30" open source CNC machine design

    Just for you here is someone that is having a problem with his machine, just the type you have been talking about https://www.cnczone.com/forums/uccnc-control-software/391115-
    cnc.html may be you...
  13. Re: Haas mill and lathe overvolt power problems

    On the T5 that should be ok as that is just a 24v transformer the main Transformer should be ok as well with the Jumpers in those positions, mine are the same and I have 245v on average
  14. Replies
    8
    Views
    24

    Re: spindle speed not changing

    So you have to look at the configuration of the controller MX4660 you have to get this part working before looking at the VFD Drive

    Did you supply the 10v / 12v to the MX4660 for the PWM output of...
  15. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    What you are saying is correct but if you use the Keypad only, it must be set at the max main Frequency of your spindle =400Hz to get the max spindle RPM using the Keypad using the remote control...
  16. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    Not at all PD003=400 that's the main Frequency that the Pot or the Keypad requires for manual control you can not set this lower than your spindle max Frequency

    PD007=20 is the starting Frequency...
  17. Replies
    25
    Views
    40

    Re: 30x30" open source CNC machine design

    First off you said you could make it for X amount of dollars, then you complained that you could not find extrusions that you could epoxy steel tube into, I gave you some choices did not say you had...
  18. Replies
    8
    Views
    24

    Re: spindle speed not changing

    First you have to check 0-10v is working from the Breakout Board and this changes with the M3S12000 should be 5v

    VFD Drive Model and number Manufacture
  19. Replies
    25
    Views
    40

    Re: 30x30" open source CNC machine design

    The are hundreds of hobby guys that have built simple machines to start with and then built better machines once that see the short comings of the first build, just trying to move you past the first...
  20. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    So as I said they where nothing to worry about as what is in the fault report has nothing to do with how it is running, they probably where from the factory testing and where never cleared, you have...
  21. Replies
    19
    Views
    36

    Re: Huangyang 2.2kw VFD pd177-180 Errors

    It is not advisable to do a Factory Reset unless you really have to quite often this can mess up these Huangang VFD Drives

    So did the Faults stop the Spindle from running ???

    Or was it just...
  22. Replies
    6
    Views
    10

    Re: 6040 X axis strengthening again.

    It's hard to say, if it is going to help, is this to help with the Z axes top mounting plate from flexing, the Ballscrew has a lot of power so may still push up even with your mod, Box the whole Z...
  23. Replies
    90
    Views
    2,233

    Re: 60" x 40" new build

    How did the Gantry work out after filling it
  24. Replies
    25
    Views
    40

    Re: 30x30" open source CNC machine design

    Yes there is a market for suckers and those that don't know any better
  25. Replies
    25
    Views
    40

    Re: 30x30" open source CNC machine design

    Yes your are correct, in the Video though at 2.32 he is calling the Linear Bearings (A 4 Wheel configuration ) someone that builds a machine like this and does not know the correct names of the part...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4