Hi all
I have just purchased the above vacuum former.But didnt have a user manual with it.
Does anybody else have one that i could have a copy of.Looks like a nice bit of kit.Never used a vac...
Type: Posts; User: nealg
Hi all
I have just purchased the above vacuum former.But didnt have a user manual with it.
Does anybody else have one that i could have a copy of.Looks like a nice bit of kit.Never used a vac...
Thanks for that.I'm getting a reading of 3.2v instead of 3.6v is that enough of a drop to loose settings
cheers Neal
Hi all
bit of a dumb question can anybody tell me where the back up battery is.totally different to my other ez trak.having a problem booting up and as a start point I want to change it.
Cheers Neal
I thought i might get this response.It does sound a bit mad but i already have another ez trak and dont tend to use the cnc side of it.I have a hurco hawk ssm
which i do my cnc work on.In my opinion...
Hi all.I have just purchased a 1998 ez track mill.I want to strip all the cnc parts off And convert to manual mill.Would it be a straight swap for the ball screw to a acme lead screw In x and Y.table...
Hi.just a big thanks to bloke for helping on the last one.New problem is that it wont jog using the plus and minus keys.works fine with jog wheel can speed up and slow down using axis knob.but have...
Thanks Mr Bloke
Is this something easy-ish to to with a bit of research or is it a call to an hurco engineer
Thanks again Neal
Hi all
I was running my hurco hawk with no problems then when asked to in the program
changed it to low gear for reaming.Then error popped up.Spindle drive overload,reset servo drives or spindle...
Hello everyone
Just a quick question
On the BMDC card should led lights be on or off
In the picture number 1 red in on,2 red is off and
3 is flashing green.
Is this right after boot up or should...
Thanks for help
But paid a lot less than that for the complete machine,so think i will leave it 2 axis for now and have a play
to see how i get on.
Thanks for the reply.
Thats what i wanted to know that you can program in step mode.Just out of interest.where did you source
the z axis parts from to convert to 3 axis.Is it much of a problem to...
Hello everyone
I have just purchased 1997 ez trak 2 axis mill.
Sorry to ask silly question but being only 2 axis how do you add cut in z if
say milling a pocket out.Do you write the program and...
Good morning all
Having problems with hurco hawk rebooting
When drip feeding a long program it will always reboot its self between 45 and 55 mins every time.
Thought it might be something over...
Me again
Just like to say a big thank you to Al the man.Did some messing earlier and took the round connector apart
going into the servo drive motor and found one of the small black wires had come...
is there anything else mechanical to check apart from leadscrew nut or what ever you call it
cheers Al
Thanks Al and others for replies
New problem.Pretty sure drive board was part of the problem.Put board in off other machine along with
servo motor and encoder so pretty sure its not those.Now the x...
thanks Al
Just as you thought swapped x and y error followed.Just to make sure put board in the other machine
and error followed.Thanks Al
Just one more question.Is there anything else that can...
Thanks Al
Are the x and y axis drive boards interchangeable.So i could just swap those and see if error goes to y axis
Neal
Hi all
Well i have a more urgent problem
Have been testing the hurco today.cutting a dia to check if it cuts round for starters.
All seemed fine.Then ran the x and y axis up and down reasonably...
Hello
Just in the process of buying the hurco.Did some test programs on it and all seems fine.
Apart from when i put spindle speed of 2000 in it said speed to high for this machine.Also the manual...
Hello everyone.
Does anyone know any one who can repair the z axis board
on a hurco hawk 30.Must be in the UK.
Thankyou
Neal
Hi all
Have been running a old bmc40 for the 2 years with no problem but all of a sudden keep getting syntax error problems.This is usually quite away into the program about 7 or 8 hours.
The...
Hi all
I know its a bit cheeky but
is there anybody out there willing to model the euro coin
for me.The reason for this is i am trying to get my boss
to buy artcam and send me on a training...
hello
has anyone built ron Colonna 270 offy engine
I should get his plans in the next couple of days
I have decided to make it from investment castings
which i shall make the moulds myself.The...
Hi all
Does anyone know how to install anilam software onto a new hard drive
from scratch.we have a anilam 3300 mk control but the hard drive has just
packed in.Can anybody help please
Neal
Hi does anybody know if such plans exist.I know people are building them
because there is a video on this site.I am a pattern maker/cad programmer/cnc operator by trade so the parts and castings...