Search:

did you ever find an answer to this, I'm in same boat

I'm having same issue, I haven't been able to get help anywhere. The video seems like such a hack, have you figured it out?

No doesn't sound like that, I'll record it tomorrow. The motor stops and makes a buzzing sound like it is trying to move but can't, seems to only happen when going fast jog. Slow jog doesn't do it.

I haven't fired up my machine in a while and I think my pc is disconnected. I'll try and get it fired up tomorrow and get those values. Not really looking for a lot of speed just want it smooth and...

I'm having issues setting up my machine and I'm getting frustrated. Here is my machine specs:

4 Axis CNC Stepper Motor TA8435H - from here ebay
3-260 OzIn 4-Wire Stepper Motors from Probotix
14...

I've seen a few routers that have pieces of drill rod mounts cut and placed every few inches. Where can I find these mounts? See picture
...

I've been using standard end mills on my cnc router but I'm looking for some replacements. I've been using 1/4" but would like to find some 1/2" with 1/4" & 1/8" end mills for machining wood and...

I know they have G-10 but I was really trying to find carbon/g-10 cheaper than what they have.

Anyone know a source for carbon sheets and G-10? Thanks

Anyone know where to get the t-slot table tops like this http://www.k2cnc.com/DuportalPro343Access/Pictures/detail.asp?iData=134&iCat=661&iChannel=3&nChannel=Pictures

I have a ton of 80/20 but...

Well another operator error, I guess sheetcam was trying to cut my drilled holes as profiles. I guess I need to create them as points in autocad instead of holes.

I finally got everything going and when I run the g-code in turbocnc I get an error helical no longer supported use 3rd axis or something like that when I run my code. Any ideas?

Should it be negative or zero?? Thanks

I figured it out, on my tool I had accidentally put in a tool length offset

I'm trying to use sheetcam 5.0.1 to create a battery plate. When I create the G-code for Turbocnc it sends my z axis up Z1.4075 for some reason and never comes back down to the part. I cannot...

I trying to get my router fired back up after years of sitting collecting dust. I've got it moving right but my movement is off quite a bit. I'm using standard stepper motors with 200 steps...

I really don't know anything about this servo motor other than the model. It is off a rotory device I bought off a surplus website for like $15. The motor is a Glob Motors 409A582 - 12VDC

Sure when I get it done, very simple though. If you want the dwg's I can upload later today

Cool, figured it had to be. Any suggestions for toolpath software?

I have a 3d model of my router mount. I designed it in solidworks but I'm not familiar with 2 1/2d but I know that is what I need to cut it out. What format do I save the model in or do I need to...

I have a three axis router but want to add a fourth which already has a servo motor on it. Is this possible? Can I still use my same breakout board just a different gecko driver? Thanks

I was wondering if anyone could tell me why ballscrew flanges are so freaking expensive. They are more than the ballscrew nut which I would have never imagined. Does anyone know a cheap source of...

Since I've changed houses I lost my old laptop that I used on my cnc router so I connected an old pc to it and setup everything so I thought. Now when I try and job my machine the motors just buzz...

Ok, installed 98 on another partition and booted to dos, ran it again still won't jog. The parallel port is set to ECP should I change that to bidirectional? What else can I test. I don't see any...

Yep

I just fired up my cnc router after two years sitting dormant. I don't have the pc anymore that I was controlling with and Installed Turbo CNC on my 2000 machine. I cannot get it to jog. I wasn't...

I have a DB1 and haven't used my cnc mill in a couple years. I replaced the pc and needed to configure turboncnc and was looking for information on the axxuss tech db1 controller but all the links...

Yeah didn't quite understand, just need visual positioning. Thanks

These are standard JR, Futaba Servos.

I'm looking to build a camera control system using some old heli servos I have but I want it to be hard wired and be able to control the servos with preferably with a joystick but maybe with a pot or...