584,849 active members*
4,335 visitors online*
Register for free
Login

Search:

Type: Posts; User: WoodallMFG

Search: Search took 0.00 seconds.

  1. I'm not in front of the machine right now, but...

    I'm not in front of the machine right now, but yes there are sub chuck open/close buttons. When I press it, nothing happens. I can only open/close using M-codes at this time.
  2. Hyundai SKT21 LMS Sub Spindle Chuck Open/Close

    Seems like a silly issue I'm having, but I can't figure out how to use the control buttons to open and close my sub spindle chuck. M codes work fine, but I need to be able to remove my part once the...
  3. Replies
    10
    Views
    2,867

    Re: Hyundai SKT21 LMS Lathe Q Setter enable

    This is the alarm I get when I press the Auto Q-Setter button. The light on the proximity sensor turns on and off when I manually move the setter up and down, so I assume the sensor is good.... Not...
  4. Replies
    10
    Views
    2,867

    Re: Hyundai SKT21 LMS Lathe Q Setter enable

    Those settings match what I have. I've gone in and changed D8.1 to 1. Is there anything else beyond that I should look for?
  5. Hyundai Skt21 LMS Fusion 360 Post Processor

    Hello, I have Fanuc conrolled Hyundai SKT lathe. I'm currently using a Doosan Puma post with decent luck, but still finding bugs. Does anyone have a clean post available for my lathe? Thanks in...
  6. Replies
    10
    Views
    2,867

    Re: Hyundai SKT21 LMS Lathe Q Setter enable

    It looks like the Data sheet you posted might be for a newer controller. Mine says "Fanuc i Series" and the data bits aren't matching up to what you posted. Dan
  7. Replies
    5
    Views
    1,089

    Re: Fanuc Q Setter enable parameters

    I've finally navigated to the Q-Setter Ladder and it says "Off". How do I go about turning it on? Thanks, Dan
  8. Thread: Doosan M91

    by WoodallMFG
    Replies
    2
    Views
    881

    Doosan M91

    Hello, I am working on modifying a Fusion post for my Hyundai lathe by starting with a Doosan/Fanuc post which seems to be close. I'm now stuck on trying to figure out what M91 is used for on a...
  9. Replies
    10
    Views
    2,867

    Thanks, I will search that out when I get to the...

    Thanks, I will search that out when I get to the shop.
  10. Replies
    10
    Views
    2,867

    Re: Hyundai SKT21 LMS Lathe Q Setter enable

    What is D7.7?
  11. Replies
    10
    Views
    2,867

    Re: Hyundai SKT21 LMS Lathe Q Setter enable

    Interesting. It's a 2006 SKT21-LMS
  12. Replies
    5
    Views
    1,089

    Re: Fanuc Q Setter enable parameters

    Yes. Is there a specific parameter #/page I need to post? I'm new to Fanucs "ladder" system.
  13. Replies
    5
    Views
    1,089

    Fanuc Q Setter enable parameters

    Hello, I recently purchased a 2006 Hyundai lathe with a Q setter, Fanuc controlled. The previous shop never used setters so apparently it's be disabled. I assume this is done through a parameter...
  14. Replies
    10
    Views
    2,867

    Hyundai SKT21 LMS Lathe Q Setter enable

    Hello, I recently purchased a 2006 Hyundai lathe with a Q setter, Fanuc controlled. The previous shop never used setters so apparently it's be disabled. I assume this is done through a parameter...
  15. Yaskawa drive control board replacement

    I have a Yaskawa JPAC C341 ETC008572 control board from a '91 Hurco BMC 20 that went bad and I have found a replacement board, but it is a ETC008573. Is this just a newer version, or is it not...
  16. Replies
    3
    Views
    904

    Re: '91 Hurco BMC 20 Axis S Encoder Fault

    Would I be looking for a loose connection?
  17. Replies
    3
    Views
    904

    '91 Hurco BMC 20 Axis S Encoder Fault

    Hello all,
    I have a '91 Hurco BMC 20 that decided to throw an "Axis S Encoder Fault" alarm on Monday. The machine will go through the power up/calibration process, but when I select "Warm Machine"...
Results 1 to 17 of 17