Looking to sell my CNC router along with Dekker vac pump.
Email: [email protected]
2005 MultiCAM CNC router
220/380V 3 Phase
5'x12' Phenolic vacuum table
Type: Posts; User: moparx12
Looking to sell my CNC router along with Dekker vac pump.
Email: [email protected]
2005 MultiCAM CNC router
220/380V 3 Phase
5'x12' Phenolic vacuum table
Hi there,
I am in between CNC machines and need some parts burned out. Here is the breakdown:
end caps.DXF: qty 32, 14 ga. 304SS
face_plate 28.DXF: qty 6, 14 ga. 304 SS
Thanks Gerry. Yes, it has !!!SOLD!!! Good luck in your search though, I am surprised there aren't more of these out there.
!!!SOLD!!! Best of luck emassey!!
I can't seem to find out a whole lot on this topic but would like to find out if anyone on here has experience with any servo based ATC Chinese machines. I am thinking of getting one with a Shanlong...
Text sent. Pending sale.
I have a JCUT CNC router in Raleigh, NC would like to sell. It works great of course, and has a UCCNC controller in it now which makes operation much smoother....
Well, I am going to post this to the proper forum, but I want to see if there is any interested in purchasing my machine. It no longer has the aluminum bed, just MDF, and I replaced the chinese...
Hi Dave, here is the price breakdown that i went thru. Hope it helps!
2200 lb, 513 ft^3
Broker:
Customs entry fee: $125
Customs duty tax/fee: $62 (3% of declared merchandise value
...
PM'd you
1105K16 is the MMCarr part number... pack of ten for less than I paid for a single Hiwin fitting. I bet those Hiwin ones have a super high flow rate geometry and ultra slick coating on them though so...
Thanks everyone. I bought a few straight through Scott Equipment. Not cheap at almost $6 per but they shipped them within a few hours and I should have them in a day or two. Part number is listed in...
Im sure they have Zerk fittings, but these are certainly not standard. Today I found a local HIWIN dealer and they actually have their own PN for the fittings. Ill report back if they sell some to...
Great, Thanks guys. I do have a HF near, but I doubt they carry such a thing?
I found another thread on this but no real solution. I want to put grease nipples on all of my bearing blocks. I looked up the specs and found that the blocks take m6x0.75mm zerk type fittings....
Well, I've seen some shopbots that have just MDF on top of the box tubing structure so I think I'll give that a go. The spacing between supports is about 8-9" so I think it will be stiff enough.
I bought a 4x8 Chinese CNC machine last year with water table. I never ended up cutting aluminum and need to be able to cut a lot of sheet goods. I have 2 Chinese vac pumps that I plan to hook up in...
I just wanted to post on here to let others know about my experience with JCUT CNC, specifically dealing with Mandy from whom I purchased a 1325B machine from a little over one year ago.
You can...
I was steered to 2 very small vacuum pumps when I inquired. Maybe this will help you. I didnt get a pump at first but asked about them recently to compare pricing.
From Mandy:
"The cost of...
Good luck with 50/50. They would not ship the machine until they recieved 100% in my case and I don't blame them. Your purchase is supposedly protected on Alibaba.
The machine is working just fine! I have since converted to UCCNC and am running an ethernet motion controller, UC300-ETH. I do not like the leafboy controller that comes with the machine, although...
For the UCCNC developers, is this something on the "list"?
It worked! I had to set the IP address on the desktop PC and it finally connected using the crossover cable.
Thanks Gerry, I will buy a 25 ft straight cable if the LAN card I get today does not work with the crossover cable. The straight cable I tested with is not long enough and I don't want to use the...
I have the UCCNC UC300ETH-5LPT with C10S BOB. I am in the process of replacing a USB Leafboy77 board with these new components in my machine.
Are you guys using the crossover cable for a direct...
I am trying to design a stationary router table and will be purchasing the Bosch 1617 later today. Does anybody have and would be willing to share with me a drawing or DXF of the hole pattern? I want...
Alright guys thanks for the help. I think i found the culprit. The grain pattern in oak appears to vary in hardness by enough to deflect my 1/4 inch compression bit considerably. I ran a test part...
Ok so x is calibrated at 44 inches and y at 90 inches using the fatmax. I will run a small test part tomorrow to see how it does! If its still cutting oversized i will report back.
It is a cheap empire brand straight edge you can get at the local box store. I have a 16' fatmax tape I could check against.
Yep, It looks like I was off. the x axis was a little worse than the y but both appeared to be around .010" overshooting at 34". I made the change in mach and ran a new program. Since i can measure...