584,808 active members*
5,362 visitors online*
Register for free
Login

Search:

Type: Posts; User: hutch07

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Haas VF2 error: ENGLISH LANGUAGE NOT FOUND!

    I have a 2007 Haas VF2 and I am getting an error on start-up:
    ENGLISH LANGUAGE NOT FOUND!
    M1805ENA.bin NOT FOUND!
    M1805ENA.lpk NOT FOUND!
    COPY BOTH THE .LPH AND .BIN FILE ONTO THE USB STICK....
  2. Replies
    6
    Views
    2,392

    Re: Nakamura-Tome SC-250 Maintenance Manual

    I do not have those any longer.
  3. Re: G41 BOMBS every time in post process Haas VF3 CAMWorks

    391350 I had to add compensation to the lead in lead out and tweak the settings on the profile. There must be a default setting to make sure this is always on. I'll check.
  4. Re: G41 BOMBS every time in post process Haas VF3 CAMWorks

    It looks like if I use near zero "D" offsets this will run. This post processor looks like it sucks.... Is there a way to have it use actual tool diameters in the machine or only zero with a bit...
  5. G41 BOMBS every time in post process Haas VF3 CAMWorks

    I have a simple profile and no matter what I choose on CAMWorks for Solidworks 2018 , the post processor will not get it correct. I am running this on a Haas VF3 and this actually calculates I and...
  6. Okuma MA-500H-II ATC Magazine 16894 Pot remove horizontal position is not completed

    We had a part stick onto a drill and attempt to be put away into the magazine. Nothing is broken and we slid the part off the drill. However, the robot arm on the magazine did not finish it’s...
  7. Replies
    7
    Views
    1,825

    Re: Okuma OSP-P200L parts counter

    All this was a good find . The OSP-300 book shows Work Counter VWRKC[α, β]

    I have never been able to get this to work. VWKCC[α] works fine with α being 1,2,3 or 4.

    1: Work counter A
    3:...
  8. Replies
    4
    Views
    1,656

    Re: Okuma Genos with OSP300 using IGF

    Thanks Deadly!

    Those are great ideas. I did try to set the two before the transfer but there is an M151 code that synchronizes the B spindle to the A spindle using 2nd spindle zero offset in the...
  9. Replies
    4
    Views
    1,656

    Okuma Genos with OSP300 using IGF

    We changed the “A” – Left Chuck to grip the points.

    When the IGF writes the program it uses the M151 to sync the spindles. Does this use a parameter to set the “B” sub spindle angle ©? No...
  10. 2395 Alarm-B User Reserve code 92 ‘PROBE OPEN’

    We are having issues with our Renishaw RMP60 probe and the RMI-Q reader. The Okuma COntrol is an OSP-300

    2395 Alarm-B User Reserve code 92 ‘PROBE OPEN’

    We have swapped out the Probe and still...
  11. Replies
    2
    Views
    1,499

    Re: Haas EC-400 APC lift cam may be damaged.

    The 3 balls had major contamination. Pounds of rust and dust in the cam tracks. While we had it open we replaced :
    (1) 51-0152 BEARING TAPERED ROLLER
    (3) 59-0616, BALL 1 7/8 APC
    (1) 20-2110A...
  12. Replies
    0
    Views
    838

    Okuma MA-500 II

    Our issue was with the Okuma MA-500HII 642.191290 – OSP-P300M control has an alarm 1703-03.

    In the Diagnostic screen when we are in Handle / Manual mode with the MPG we see

    • Axis Interlock...
  13. Replies
    4
    Views
    1,411

    Re: Need Haas vf1 post process

    HSMExpress by autodesk is free.
  14. Replies
    2
    Views
    1,499

    Haas EC-400 APC lift cam may be damaged.

    Looking for help finding haas 2005 parts for an EC-400. The lift on the APC will not go all the way up and I think it is the cam on the inside. It looks repairable from the manual but I am...
  15. Re: How to match Timing pulleys and timing belt? (noob question)

    Gates has some excellent "how-to's" on their site. I think there is even a calculator for center distance with each of the pulleys and belt. If you are using the same pitch pulleys and belts...
  16. CL-203 X Axis needs alignment to the spindle.

    When I set-up a flat disc in the chuck and tram it in to zero on the indicator, the disc is not perpendicular to the X axis. It is cutting a convex part 0.004" high in the center of the part. ...
  17. Re: RS232 link problem on CL200 with M64 Controller

    I am having the same issue. I will try these settings and report back.

    Mori Seiki MSC-803 on a CL-203


    THANKS!!!
  18. Replies
    7
    Views
    2,536

    Re: SPINDLE OR ROTARY TOOL SPINDLE ON ALARM

    1171 taprov Tap return
    override
    Set the tap return override value for the synchronous
    tap.
    1 to 100 (%)
    1172 tapovr Tap return
    override
    Set the override value when leaving the tap end point...
  19. Replies
    7
    Views
    2,536

    Re: SPINDLE OR ROTARY TOOL SPINDLE ON ALARM

    Is there a machine parameter that would cause this?

    FROM THE PARAMETER MANUAL


    12 SYNCHRONOUS TAP CYCLE ACCELERATION/DECELERATION TIME
    CONSTANT ERROR


    The time constant has not been set...
  20. Replies
    9
    Views
    5,633

    Re: Dnc problem for Mitsubishi Meldas 520AM

    molgora,

    How are you send from Machine to PC - Device 0 "Punch".
  21. Replies
    7
    Views
    2,536

    Re: SPINDLE OR ROTARY TOOL SPINDLE ON ALARM

    I still have not found anything on this MSC-803 Mori/Mitsubishi control
    (flame2)
  22. Replies
    7
    Views
    2,536

    Re: SPINDLE OR ROTARY TOOL SPINDLE ON ALARM

    Not_In_Use THanks, I will try that.

    I did write the code out long hand ;

    I CHANGED MY ZERO POSITION. The face that gets tapped starts at Z-0.500.

    G00 Z-0.25
    M03 S150
    G63...
  23. Replies
    7
    Views
    2,536

    Re: SPINDLE OR ROTARY TOOL SPINDLE ON ALARM

    This is a Mitsubishi Meldas Control.
  24. Replies
    6
    Views
    1,371

    Re: Mori manuals for sale on ebay

    The link above just takes me to the Ebay site. Do you have a store on there?
  25. Replies
    7
    Views
    2,536

    SPINDLE OR ROTARY TOOL SPINDLE ON ALARM

    All,

    I am trying to Face Tap on a Mori Seiki CL-203B Machine. The machine goes in fine to the -0.625 point and then will not reverse the spindle and feed out.

    I get the EX0401 ( G1027)...
  26. Re: manual cam t2 mitsubishi

    Dano_St did you ever receive manuals? I am also looking for them.
  27. Replies
    4
    Views
    7,521

    Re: 1/2-14 NPT Programming

    ½ - 14 NPT Male thread Inch Programming

    Thread Pitch 0.07142 Thread Taper 1:16 on Diameter
    Thread Height 0.05714” Root Diameter at start 0.6977
    Root at finish 0.7485”


    T0909 (THREAD)
    G90...
  28. Replies
    78
    Views
    15,048

    Re: Fanuc OT Manuals

    319594

    The only thing on the start-up screen. Is there somewhere in the control that I can tell which version it is?
  29. Replies
    78
    Views
    15,048

    Re: Fanuc OT Manuals

    319592

    This is my control. It is an OT but I do not know what version it is. I am looking for manuals. Thanks in advance for any help.
  30. Thread: spigot failure

    by hutch07
    Replies
    34
    Views
    13,150

    Re: spigot failure

    319342


    This is ours. We'll be tearing into it... It has voltage at the motor but no movement.
Results 1 to 30 of 122
Page 1 of 5 1 2 3 4