If you see my last post on this issue things have not changed and I have looked ever where for some info and nothing is out there, I read the install manual for mach3 and found nothing that is any...
Type: Posts; User: PJRU0304
If you see my last post on this issue things have not changed and I have looked ever where for some info and nothing is out there, I read the install manual for mach3 and found nothing that is any...
A Axis is enabled and it is used for a slave to the Y axis so no it is not in degrees, however the B is also enabled but I'm not so sure it is in degrees because I don't remember if I did anything to...
Okay so I just installed my Rotary axis on my DIY CNC and because I used NEMA 34 motor on the other 3 axis I did the same for this axis, so after getting it hooked up I went into mach3 copies my...
I didn't think so either, have been running mach3 for 2 yrs and something happened to the control PC so I replaced it with a refurbished one from ebay , it came to me with a 64 bit windows 7 and so i...
Okay so after getting an all new (refurbished) windows 7 PC and a new PCI parallel port card everything seems to be running.. or is it? when I start a gcode everything starts fine then after about 3...
thanks for the help... happy to say that I just now got it back up and running. After all that it was the PP card, I replaced it and changed the settings for the new card and it started running fine,...
so if you go to Windows 10, will you still have a parallel port card? and if not how will you connect to BoB? Using a UC100 adapter? I was using one of those and I think either it (UC100) was bad or...
thanks Gerry, I just looked and it is a 64 bit, crap!! i just ordered a copy of 32 bit W7 software and I will give that a try. the whole reason for changing the PC is because after installing the...
I had to change my PC because of some issues with the monitor output , it was just easier and buying a refurbished PC on ebay with Windows 7 and 1 yr warranty is less than $75 so i did just that. The...
So now that I have a new Breakout board and added a UC100 USB adapter configuration and Mach3 reinstalled I am getting voltage from output pin #17 to work on mach3 to output PWM for the TTL wire on...
I have been trying for days to get my new Endurance 10 watt Diode laser to work with PWM on the TTL wire coming out of the Laser board. According to most info I can find it is as simple as assigning...
So after many hours trying to get this right, come to find 2 things...
1: after replacing the parallel port card the resource ID needed to be change changed in mach3 ports and pins . I guess I...
looks like the problem is in the stepper drivers because I have now replaced the parallel port card and I have replaced the breakout board and still nothing so I checked motor supplies and they are...
I was cutting a project on my DIY CNC and when I stopped to change bit the machine stopped working? I tried to move gantry to zero and all it would do is make a bump sound, the way it always sounded...
each motor has it's own power supply, I thought about that and tested each, seem okay. When I power up control panel I get a bump from the motors locking in position, and that kind of feels right....
So after sending this post this morning I took a look at the connections to try and find a problem, nothing was visible. I unplugged the DB-25 and unplugged the RS-485 and also unplugged everything....
I have a 1000 x 1200 mm DIY CNC Built over time with what I could afford along the way. I finally got it running a year ago and started cutting wood and other and it worked well for a beginner. Along...
I just did that and WOW it works like the old days!!
Thanks man, I just can't believe that got past me for weeks, duh...
Thanks again
Pat
okay now I feel like a fool... I think it is going in reverse. I only found one setting in the Huanyang manual for that parameter and it seems to be set correct? but that must be the reason. Do you...
I am looking for some help on this issue and it's making me crazy now. Here is a small back story.
2 months ago my Huanyang Spindle Inverter went bad? I am running a 2.2Kw spindle through the...
okay it seems that the mach3 error was because I had output 6 turned on in the ports and pins from when I was setting up the GT inverter, so that error has now gone away and I am still left with...
I have been working on replacing my Huanyang 220v Inverter for the last few weeks and after going through 2 exchanges with Huanyang I have gone back to the original Inverter I had it was the "HY"...
i have a DIY CNC that i built about a year ago and it was working fine until it wasn't, the Inverter stopped working. i ordered a new one from Amazon and received an email from Huanyang asking if i...
I had this posted on the wrong forum for a couple of days so i changed it a bit,
after already changing the invert-er one time because it failed, again I need to replace or repair it. Because it...
you are right i am sorry i will move it over to the right place, i did mention in my posts that i use mach3 i'm sure but i am sorry for the screw up,
any idea where one might look for such a implement?
thank you and I have already done this process and it works fine the problem is getting it to work though RS485 now it seems there is a problem within the plugin and I have been looking for one, so...
thank you I did change all the parameters that needed to change before trying spindle, I was given instructions from Huanyang, i did go over everything last night and found something i am going to...
after already changing the invert-er one time because it failed, again i need to replace or repair it. Because it is still under warranty it was replaced with the "GT" model? So after installing it i...
that's the part I don't get either? at the end of a run it comes right back to zero, right on the dot. it is very consistent so I went into the script editor in mach3 and made a change on the script...