584,805 active members*
5,350 visitors online*
Register for free
Login

Search:

Type: Posts; User: tuanpq

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    27
    Views
    9,046

    Re: Hitachi Seiki TF20

    please send me a copy [email protected]
  2. Re: How do I backup programs to USB on OSP-E100L controller?

    Floppy usb emulator for read is easy but for write is difficult. So I think that, the problem is in usb emulator.


    Sent from my iPhone using Tapatalk
  3. Replies
    11
    Views
    2,260

    Re: OSP file floppy 8" to PC

    You should use usb to fdd ide converter. You must have electronic skills.


    Sent from my iPhone using Tapatalk
  4. Re: Default Hydraulic oil flooding out the spindle b212 kitagawa chuck okuma lu15 imp

    Remove it from back


    Sent from my iPhone using Tapatalk
  5. Thread: BL/PREX motor

    by tuanpq
    Replies
    8
    Views
    1,529

    Re: BL/PREX motor

    BL motor is synchronous motor.


    Sent from my iPhone using Tapatalk
  6. Replies
    17
    Views
    2,522

    Re: Amada Fanuc PEGA 357 no booting

    Master board error


    Sent from my iPhone using Tapatalk
  7. Need help makino professional 3 MSA50 parameter

    I have makino professional 3 MSA50 lost parameter. Anyone have the parameter. Please help me. Thank you in advance.


    Sent from my iPhone using Tapatalk
  8. Re: How to replace servo drive in HITACHI HG400III

    I think that it have no error but it is no good.


    Sent from my iPhone using Tapatalk
  9. Replies
    1
    Views
    486

    Re: NEED HELP QT-15 w/T-2 control won't play

    Check 24v power supply.
    Upload picture of led light in pcb of T-2


    Sent from my iPhone using Tapatalk
  10. Replies
    1
    Views
    389

    Re: Mazak SQT15 how to disconnect barfeeder?

    I used to do it with hardware. but I don't remember it for a long time.


    Sent from my iPhone using Tapatalk
  11. Re: HELP! Hitachi Seiki HT-25G HPC1 lost configuration

    I can fix it.


    Sent from my iPhone using Tapatalk
  12. Replies
    6
    Views
    663

    Re: only half spindle speed

    you seem to have checked all of them . Did Your machine reloaded system software?


    Sent from my iPhone using Tapatalk
  13. Re: OKUMA OSP-P200 machine 955 ALARM-P spec code:data file 1515xxxx

    Reload software


    Sent from my iPhone using Tapatalk
  14. Replies
    9
    Views
    1,041

    Compatible encoders?

    You must buy same encoder because your motor have hollow shaft. Screw move through motor.


    Sent from my iPhone using Tapatalk
  15. Replies
    9
    Views
    1,041

    Re: Compatible encoders?

    What kind of machine. Your encoder is high speed and high resolution encoder. This encoder is rare.


    Sent from my iPhone using Tapatalk
  16. Replies
    9
    Views
    1,041

    Re: Compatible encoders?

    Can you take picture of motor and encoder?


    Sent from my iPhone using Tapatalk
  17. Replies
    13
    Views
    1,066

    Re: Fanuc drill mate option parameters

    You check email


    Sent from my iPhone using Tapatalk
  18. Replies
    13
    Views
    1,066

    Re: Fanuc drill mate option parameters

    This is what I think. Original your machine use master pcb same as my machine. But your machine is rebuild with other master pcb so you should find rebuilder


    Sent from my iPhone using Tapatalk
  19. Replies
    13
    Views
    1,066

    Re: Fanuc drill mate option parameters

    Your master pcb is not for Fanuc 0-mate. it is rebuilded. my machine master ocb is in picture
    463486.
  20. Replies
    5
    Views
    1,130

    Re: Trumpf Trumatic 180w WITH FANUC 6M

    You replace IO board


    Sent from my iPhone using Tapatalk
  21. Replies
    10
    Views
    1,427

    Re: Mazak slant turn 35N ATC parameters

    It has T3


    Sent from my iPhone using Tapatalk
  22. Replies
    19
    Views
    5,168

    Re: FANUC DOWN AGAIN. 914 RAM Parity Servo OM-B

    TMM2089P-45 4 ICs in red circle 459132
    you can replace by MB81C79A-45P
  23. Replies
    19
    Views
    5,168

    Re: FANUC DOWN AGAIN. 914 RAM Parity Servo OM-B

    458986
  24. Reset program zero at current position using Macro B

    Edit #1=#4014

    You copy macro from other machine. So if you want to run on your machine you must edit macro


    Sent from my iPhone using Tapatalk
  25. Replies
    8
    Views
    836

    Re: Fanuc 18T PMC Program EDIT

    Fanuc 18T use EPROM to store PMC ladder, so you don't edit it by Ladder III software. you can read it by Ladder III sofware.
    457940
  26. Replies
    19
    Views
    5,168

    Re: FANUC DOWN AGAIN. 914 RAM Parity Servo OM-B

    Master board error.


    Sent from my iPhone using Tapatalk
  27. Re: Mazak VQC 20/40 Mazatrol M2 Freqrol PLG with external Encoder for orientation

    Do you try increase speed slowly from 0 ? How much rpm when over speed error appear?


    Sent from my iPhone using Tapatalk
  28. Re: Mazak VQC 20/40 Mazatrol M2 Freqrol PLG with external Encoder for orientation

    I think when you connect cable, phase is not correct.


    Sent from my iPhone using Tapatalk
  29. Re: Mazak VQC 20/40 Mazatrol M2 Freqrol PLG with external Encoder for orientation

    Do you disconnect u v w cable. If yes then you check u v w cable


    Sent from my iPhone using Tapatalk
  30. Replies
    10
    Views
    1,427

    Re: Mazak slant turn 35N ATC parameters

    Can you help me parameter of Mazak slant turn 40N ATC m/c my email: [email protected]


    Sent from my iPhone using Tapatalk
Results 1 to 30 of 112
Page 1 of 4 1 2 3 4