Search:

You should have this as a sub program here it is for a ball screw T42 sub spindle full program below go slow to test it and have a special cut off (if bar work that will fit between both spindles)
...

I checked for 100 VAC that is good 24VDC is good our 3 phase is delta
When it shuts down Y jerks about .100
When the control is open all the way it will stay on a long time close the panel and in...

I have an EM 500 trying to test why the drives shuts down.
The machine power up by pushing red on button twice.
1st push turns power to computer.
2nd push turns on drives.
My first test was to...

I have all the parameters and know how to manually to load them. got to scan them
Just did my EM 500 with 3000G control and CRT display
Let me know

On My EM 500 1982 with 3000G and CRT
In tape box look for rotating switch and select 1 then go to control parameters and select parameter 59 change X to 3 and Z to 13774 that will be 1200 baud rate...

Hi I have a Ikegai with a Fanuc 6T control and when I add my offset values my CRT adds them to the screen value so if my program was written to say GO X1.0 Z-2.0 and I add say X-.800 and Z-.500 in...

Problem solved Fanuc Board next to X Z (RH side) drives had loose ground. cleaned the contact points and removed the board and sprayed contact cleaner and machine is now working fine.

Thanks for the reply,
This is what I have
IKEGAI AX25 Lathe
TURRET 12 position indexes hydralic and rotates hydralic motor factory made
Fanuc 6 T contol
Has a Sumtak Index pulser

Does anybody have advice for a turret that indexes random I tried to rotate index pulser and dgnos 700 701 712 are zero and stay zero?????

Delw,
This only show's the "IDEA" to get the patent, production models will be mounted to the floor and have guards and an eletronic vibration sensor to RESET machine control should a slightly bent...

JHCOPPERS
Thanks for the remarks, We are working on drawings and a prototype of a manufactured model.
I have had a lot of people who are interested in one for there CNC

Thanks for the reply.
The device has collars that adjust rollors smaller to the different size bars this one goes from 1.375 down to .375
Two different models use either direct bar contact or for...

YouTube - CNC BAR FEEDER

MY CNC BAR FEEDER ON A SUPERSLANT HARDINGE PATENT PENDING

The rollers adjust from 1.375 down .375 by rotating a collar and locking in place or there is Type 2 a driven tube that uses liners to center hex or square stock. and for now I am working on 6 foot...

Yes to be a bar feeder it needs a pusher and that can be added with a end of bar detector and feed hold or reset circut to stop the CNC at the end of
the stock

It has been run at 3500 rpm and it should do 6000 rpm with roller every 4 inches it does not vibrate, I have run this one about 1000 hours and no wear
so we plan on making these for six foot bars
...

MY CNC BAR FEEDER 6 TO 12 FOOT BARS HIGH RPM CHECK OUT VIDEO

PATENT PENDING



YouTube - CNC BAR FEEDER

That is the right part, Just make sure it is bad de-solder it and switch it to the other board "carefull to get all the solder out" dont forget to change the jumpers. and set offset trim pot small...

.

To use M21 both turrets must be "ON" OR M21 WILL NOT WORK AND M21 ONLY WORK'S ON TURRET #1.. here is A program USING A FINGER BAR PULLER
G0Z-.5 MOVE PULLER TO BAR END
X0. MOVE PULLER TO GRAB BAR...

Luis M.

The Fanuc part FIXED MY OLD MACHINE I am glad they still make some of the hard to find parts, for me $168.00 was cheap compared to the service call, new board ect.
Many Thanks to this...

We have in stock. The price each is $168.00.

Thank you for the inquiry - ordering contact information shown below.

Best regards

Luis M.


GE Fanuc Terms and Conditions of Sale apply to...

I FIXED MY IKEGAI AX25 FANUC 6T AS SUGGESTED 401 SERVO AND HCAL LED LIT.
1.I SWAPED BOARDS A20B-0009-0320 AND THE PROBLEM FOLLWED THE BOARD, "MAKE SURE"!!! THE PLASTIC JUMPERS LOWER LEFT HAND OF...

I have a Superslant 4 axis live tooling, I bought for $6000.00 and have made over $250,000.00 with it, the machine has turret problems, power supply, incoders ect that will go bad. It is best to send...

My Ikegai does not have a G30 or dogs to move, and I used to have to move
all the way home to index, Newer machines with 6T controllers have a work shift in the offset page and you use this as a...

I Use A G50 As Follows With Block Skip (/)
When Setting Up Switch Off Block Skip And Start Each Tool At G28u0.w0. / This Sets Your G50 And Goes Home You Do Not Have To Manuall Move Turret...

Dan thanks for the help, I tried setting bit 7 to 1 and 0 the parameter setting
that the Ikegai book says parmeter 0007 00000001
I did 0007 01000001 and 00000000
No change the control is a...

When I am say setting up the machine a running block by block and look at
the Display the off set amounts are added to the programmed value, so I
command G00 X 2.0
G1 Z-1.0 F.004
If...

I Have An Ikegai Ax 25 And Reloaded The Parameters All Seems To Work Correct, Except The Offsets Value Are Added To The Crt
Position X And Z So If I Command X2.0 And Add U.450 In The Offset
The...