On my J320 the speed control was a variable sheave belt drive with a back gear. The sheave was controlled by a closed loop D/A controller that used a prox sensor on a 10pt sprocket for speed sensing,...
Type: Posts; User: fahrphrompuken
On my J320 the speed control was a variable sheave belt drive with a back gear. The sheave was controlled by a closed loop D/A controller that used a prox sensor on a 10pt sprocket for speed sensing,...
I'm in SW Michigan. I could box and label the items. Would probably have to remove the CRT and control panels and scrap the enclosure to save on package size and cost.
I'll take some pictures of it...
Hi- Do you have the Operation, nd Installation manuals for the Delta 50? I have both that I could part with for a lot less than what I paid for them. I also have a complete Delta 50 chassis, and...
What controls does it have? I have Install and Operation manuals for the Dynapath Delta 20, along with some remaining hardware (control panel, etc.).
I also have a complete Delta 50 system complete...
Hi Larry- these manuals are for the 810m that was used on a Motion Master 3 axis router. If they can be of any help to you, you are welcome to them.
PM me for more details
Boy does that look familiar! Looks like your's is coming along nicely!
Did it have the mach controls on it when you acquired it? I am starting to consider that as an option.
My j320 came with the...
There is a seller on ebay that sells a floppy drive USB replacement unit for about $180. It fits in place of the floppy drive, and connects to the floppy control cable. Then you can use USB thumb...
Just out of curiosity, what Dynapath control do you have?
I had restored a Tree J320 that came with a delta 10, and SD servo amps. I found a deal on ebay for a delta 50 ( I think it came from a...
The "fingers" might be something related to the tool changer?
I would ask how much does it weigh? For a home shop you will want to be sure you have a pretty thick concrete floor.
I'm guessing...
Hi Jim- I sort of stumbled on to your post here, and wanted to ask a couple questions. How is the retro-fit of the J320 going? I had recently restored a J320 as well, except it had already been...
Wow, that's going way back, but you're right, even the Bendix units were housed in the black box with all of the cards contained inside weren't they? Even all the more reason to have to consider a...
Kemlin-
I sent you a link to download the electrical diagrams for the old Bendix control. This could be a troubleshooting challenge if the issues are related to the control (vs the servo drives),...
That is the System10, probably pre-Autocon/Dynapath when it was still Bendix.
I had restored a Tree Jouryneyman 320 that originally came with a System10, but was already upgraded to a Delta10 with...
I might be able to help, but will need more info.
What is the control, Autocon/Dynapath? System 10/20, Delta 10/20?
Can you post some pics of the electrical/control components?
What servo drives are you using? It sounds like one possibility is something wrong with the tach voltage output from the motor, or the wiring to the motor.
If the encoder signal is being picked up,...
Well, come to find out I had page 33 all along. Guess I should have paid more attention to the page #'s on the drawing sheet, than in the pdf file.
Will-
Do you happen to have any of the pages past pg 21? I am trying to get the speed control working, and there is a reference to page 33 for setup of the speed control.
I have used the file you...
Awesome post for sure!
I actually had the issue with a Delta 50 constantly rebooting itself. I discovered that if I disconnected the +12vdc line going to the CRT, it would not reboot as often,...
I think that's the power supply sticker, so your close. The sticker should be on the unit that looks like this (on the left)...
272850
The sticker should look like this.....
272852
Correct. I think any MTE-4090 will have all the correct specs, just as long as the encoder, the tach voltage, and the connector is correct.
Also, if you look on the Dynapath chassis/card cage,...
The encoder needs to be 1000ppr and the tach needs to be 7v/1k rpm. Are you using the ServoDynamics 1500 series servo amps? Those are what most of the MCP packages used to replace the original Gould...
This is the standard servomotor that Autocon included in the Delta MCP upgrade package. It is the same motor for all three axis. These are the ones on my J320. I have seen a few of them on ebay for...
It's really just a housing, and two pulleys with a cogged belt (just like the X). Here is a link to the gallery :
Message - My Photo Gallery
I'll dig up pics of just the housing assy.
The...
Do you have the Y drive housing (motor mounts to the back side)?
Hi- Nice find! I have a J320 and it looks real similar to your 330. A LOTof the parts look identical. I'll get some pics of the Y drive sprocket setup, and other parts and send the link to you....
Hi J320 owners, I stumbled onto this post, and was just wondering how these projects have panned out. I have recently finished a J320 build that came already upgraded to a Delta 10. Now I have a...
Was this the one you were talking about?
Tree Heavy Duty Vertical Mill Milling Machine with Vice Collets | eBay
Looks like possibly a J200, although all of the axis motors had been removed.
Which Delta, 10/20, or 40/50?
Man that all looks real familiar. I just finished a complete rebuild of a Journeyman 320 a little over a year ago ( fahrphrompuken Gallery - My Photo Gallery ) . It looks like they use a lot of the...
Trying to find a filter element/cartridge for this filter unit (see pic).
It's a 25 micron filter housing, but there was no filter element inside so I don't know what to look for for a replacement....