502,249 active members
7,038 visitors online
Register for free
Login

Search:

Type: Posts; User: AMADAJOE

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    69

    Re: AMADA APX100/30 - software problem?

    1. What version software? I may have 4.17 self extracting

    2. After reload software if still same condition CPU maybe faulty. I may have 1 CPU, I can load with software and send to you.

    3. Email...
  2. Re: Fiber Lasers...who makes the best? Mazak? Bystronic? Trumpf? Mitsubishi? Other?

    All good info. The only thing I would add is resale value. If at some point you decide to upgrade selling off brand equipment can be difficult.
  3. Replies
    10
    Views
    757

    Re: Fanuc 6M parameters

    I generally set 340=3 341=3 that tells 6M look at param 312 I set 312=00011010 2 stop bits & 9600 baud.
    On set page( if uploading param to laptop)
    punch code 1=
    input device=1
    input device 2=1...
  4. Re: Pushing constatly Start pushbutton for change tool working Pega II Amada

    I emailed you info, if you dumped memory you need to load PC parameters in manually. The 6M does not have the function to read in or out from the port for PC param. They are located under the...
  5. Re: Pushing constatly Start pushbutton for change tool working Pega II Amada

    I am not sure what model you have. If it is P344 check diagnostic 48.7.
    That is bit on far left. See if it changes as you push single button on and off
  6. Re: Pushing constatly Start pushbutton for change tool working Pega II Amada

    How did you load parameters in? By hand? Did you load all your timer parameters? Give me machine model and turret layout, maybe I have a parameter list. Email me at work JOE@ALTPARTS.COM
  7. Re: Amada RG-100 with NC9-EX controller shut off with lower limit on.

    415692

    Press and hold Lower Limit switch in yellow circle. Have some one start hydraulics. Once Hyd are started move ram up and down. You may have mechanical bind. I have seen a piece of...
  8. Re: Pushing constatly Start pushbutton for change tool working Pega II Amada

    Sounds like you are in Single Mode. If this is a Fanuc 6M top left side of Mode Switch (Single). Make sure this button is out = off.
    If its 04PC you will have blue button Single. Led should be off.
  9. Re: Amada RG-100 with NC9-EX controller shut off with lower limit on.

    415668
  10. Re: Amada RG-100 with NC9-EX controller shut off with lower limit on.

    Usually people leave the ram lock lever on the left side on (down). release the lever. you should have a yellow button on the face of the ram. Ram Lower with amber light. Press and hold button.
  11. Replies
    3
    Views
    101

    Re: Request for operation manual

    Lapis Services? What do you guys service. LOL.......

    Joe Lewis
  12. Replies
    5
    Views
    149

    Re: Amada LC 1212 A2 Fanuc 16L Alarm

    Sorry I did not see the email. Can you resend? CC, Amanda@altparts.com
  13. Re: Amada Vipros 414 servo alarm. Please Help

    Drives do not have codes unless you have a problem with the drive. 414 is X axis issue, usually I look at feedback cable 1st encoder 2nd. What Vipros is this? V357 w/ 04PC or V255 w/18P
  14. Replies
    29
    Views
    1,188

    Re: 1kW Chinese fiber laser cutter

    This is a very important point, many end users do not consider. Support after the sale! Parts, service, documentation and tech support. I have witnessed many customers buy new equipment from off...
  15. Re: Manual book and hydraulic diagram Amada Shearing H-3013

    Why are you overcharged on your accumulator? If you are @ 60 bar and manual says 30. You need to drop it big time. I have never had any reason to adjust valves. If you are going to move valves,...
  16. Re: Amada Coma567 not detecting work clamps. Will not prevent work clamp punch event

    No problem, Email me, its easier for me to share info
    JOE@ALTPARTS.COM
  17. Re: Amada Coma567 not detecting work clamps. Will not prevent work clamp punch event

    Check the rollers under the clamp. Check condition of brass bar. When the clamp rolls onto the brass bar it grounds it. You also need Y axis Override limit to be made in order to get override confirm...
  18. Replies
    7
    Views
    411

    Re: Fanuc 6M macros and subprograms Newbie

    "Macros in an Amada are written by the user" Not all macros are created by end user

    When I say no macros in an Octo, I am refering from the factory. If end user created a macro no one will have a...
  19. Re: Manual book and hydraulic diagram Amada Shearing H-3013

    1st off you need to run the correct oil. Amada techs dont put in various oils and record what happens. 2nd I would check your accumulator pressure. When ram reaches bottom of stroke do you hear a...
  20. Replies
    7
    Views
    411

    Re: Fanuc 6M macros and subprograms Newbie

    I have never seen an Octo with Macros. Unless you have a strange option like programmable work clamps or running a sheet loading system. But even in that case we were changing the ROMs on the PC...
  21. Re: Amada Promecam APX100 getting into BIOS settings

    Hemikiller, Thanks for the kind words.

    Cheers
  22. Re: Amada Promecam APX100 getting into BIOS settings

    "It's too old for Amada to know, their engineer told us to write- off the machine." LOL..That is funny. You need a special cable to hook up standard PC keyboard. Email me pictures of your CPU. Amada...
  23. Replies
    5
    Views
    149

    Re: Amada LC 1212 A2 Fanuc 16L Alarm

    email me joe@altparts.com
  24. Replies
    1
    Views
    312

    Re: AMADA ARIES 255 CNC TURRET PUNCH

    42KG
  25. Replies
    5
    Views
    149

    Re: Amada LC 1212 A2 Fanuc 16L Alarm

    Inspect you tubes for a hole or crack. How many hours on the resonator? Perform internal leak test.
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4