Thanks Algirdas, I'll do that in a few days and send a pic for a reference when I do
Type: Posts; User: gunda
Thanks Algirdas, I'll do that in a few days and send a pic for a reference when I do
Can you try explaining with a bit more details so I can better understand where to look at?
I can send some pics if you can giude based on them
Hi Deadlykitten, thanks for joining the discussion.
Are you referring to the pull studs of the toolhlders or other? This Multus machine has HSK 63
Seals are rubber, I replaced only the one in the groove on the other part, not the LH bolt because with the mechanic we both decided we'd rather think it over as it was requiring more disassemble.....
Do you think it could be the seal that sits in the groove or the other one on the LH bolt?
I bought a used machine an it's leaking at the back of the spindle when I run the through coolant. I was advised it's most likely this part that fails because of some reason - o-rings, scratch on the...
Hi group,
Does anyone know an aftermarket rotary joint to substitute this one
H0019-0008-28
ROTARY UNIT
TYPE: ESX20S-9534Y
https://www.ebay.com/itm/404172653015
Thanks for the ideas, I'll test tomorrow and let you know
Machine is a Multus B200-W
I don't see the Servo System parameters page in the list of parameters. Is it locked/hidden?
I am referring to the Test Mode (as called in the Okuma manuals) that allows for feeding while the door is open (with the safety button pressed of course) and it also decreases the rapid feedrate in...
Hello Okuma guys,
Does anyone have an idea if there's a parameter controlling the Feedrate limitation in Test Mode (the one you trigger it with the physical key on the control).
Normally when...
Thanks Bushmaster, I think it was your post processor I found and edited a bit. Works fine!
The thing I am missing is how to program the spindle phase on Fanuc. From the video for Siemens it is obviously SPOS,
Thanks deadlykitten, I think I know what you are speaking about, but I am searching for a solution with phasing
See below how this is made possible with Sinumerik control
...
Hi all,
I have maybe a bit of a specific question regarding a milling operation available for other controls which I don't know how's enabled on Fanuc.
Siemens and Heidenhein call it...
Hey all!
Has anyone found a way to use locked .pst posts or make them editable? I have plenty of them but they turn out being useless for this reason
Hi guys!
Does anyone have a proven and well working post for Haas UMC 5 axis milling machine?
My idea is for example is a setup consisting of a tombstone with lets say 4 sides and 4 pieces each side and G15 H1 is the WCS in the center of rotation of the table/tombstone at the base of the...
Hey deadlykitten, sorry for the delayed reply. I read your post on time but couldn't reply any sooner.
What app do you use to manage the tool offsets for Okuma. I checked their website and didn't...
Thanks for the ideas Deadlykitten, I think all of them are very well applicable.
When speaking about looking for the same solution yesterday I thought it would be a good idea to have the whole...
Luckily I did find a good post to use.
Can you guys share how you approach the fixture offset tracking (for Okuma) or in general the zero shifting for multiple parts and multiple sides?
Hi all!
Can anyone possibly share the probing add-in for Esprit? Just direct message me, it will be much appreciated and I am sure I have some Esprit stuff for exchange :)
Cheers
Hi guys,
I am in an urgent need for a good post for a simple horizontal Okuma MB series. If anyone has and is willing to share I'd gladly share something in exchange.
Cheers
Hi guys,
I am trying to setup a Swiss type machine having a tool station attached to the sub-spindle and in this case there are 2 possibilities for the tools at this station:
1 - to position the...
Hi guys
I am looking for a Tsugami Add-in for Esprit 20xx versions. Does anyone have a copy of it and be able to share?
Actually any other add-in for a swiss type machine may do as well
Cheers!
Solved - Parameter 3129 DAP1
Well, I am not the very greatest Fanuc expert but I think my approach should be good. I will attach a picture of the control tomorrow.
I was lead to think such parameter exist as I have faced the...
Hi guys!
The machine I work on is a Goodway made lathe with Fanuc 0i TD cotrol. When I program a value (say diameter 50mm) and run the program I get 50 on the actual position display. However,...
Hi folks,
I am lately having to deal with a Goodway cylindrical grinder with M70 control. Unfortunately the local dealer cannot help with manuals or instructions whatsoever.
The machine is also...