584,866 active members*
4,982 visitors online*
Register for free
Login

Search:

Type: Posts; User: Teddyo

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    497

    Re: PLEASE HELP! 6012 Acctek dead after crash!

    Thanks CNCMAN it was a fuse after all, the transformer was fine, actually the fuse had just lost contact in the holder it tested ok and when I put it back the drivers lit back up. The ends of the...
  2. Replies
    3
    Views
    497

    Re: PLEASE HELP! 6012 Acctek dead after crash!

    Thanks for responding, I just measured the output side of the PS going to the drivers and it shows a very low voltage - about .2. I can't find a fuse on the PS,looks like a chunk of iron, I will...
  3. Replies
    3
    Views
    497

    PLEASE HELP! 6012 Acctek dead after crash!

    After a recent crash - bit came loose and dove into the spoil board - the stepper motors shut down. The inverter is still on and the spindle works but not the stepper motors and looks like not the...
  4. Replies
    1
    Views
    221

    Water pump not restarting

    Hello, has anyone experienced a problem where a water pump - for spindle cooling - will not turn back on unless you drain it of water? This pump came with my new Chinese 6012.
    Please see my YouTube...
  5. Replies
    3
    Views
    286

    Re: X axis not working on new 6012

    How about if I swap the wires at the x and y drivers?
  6. Replies
    3
    Views
    286

    Re: X axis not working on new 6012

    Thank you GER21 for responding.
    The x axis is enabled in config - motor output just like the others. I'm not sure if it is set up properly in Mach3 - I assume so since I loaded the supp;lied Mill...
  7. Replies
    3
    Views
    286

    X axis not working on new 6012

    I wish I could figure out why my router will not move in the x axis on a newly purchased Acctek 6012. I am running Mach3 on a XHC MKX-4 motion card. I can get movement in the Z and Y direction but...
  8. Replies
    1
    Views
    463

    Accuracy testing suggestions

    So I just ordered a Chinese cnc router - a 6090 heavy variant - 60120 from acctek with vacuum table and rotary option. I requested that they video it running through some tests before shipment.
    ...
  9. Replies
    49
    Views
    5,467

    Re: Seeking advice for cnc machine purchase

    Thank you Ian, After having your machine for so long is there any tests you perform to see if it's calibrated right? I was thinking of having them route a large rectangle to see how well the spindle...
  10. Replies
    49
    Views
    5,467

    Re: Seeking advice for cnc machine purchase

    Hello this looks like a good place to ask ....I just ordered a Chinese 6012 (2x4') router and I've requested that they video a performance test to show accuracy and integrity before I send the...
  11. Re: My happy cooperation with jinan acctek machinery!

    Ya maybe...
  12. Thread: china machine

    by Teddyo
    Replies
    38
    Views
    2,634

    Re: china machine

    Bob I'm looking to purchase a CNC from Acctek and was wondering from your posts if they could be brokers or are they the manufacturers, which I just assumed,- would you know by chance?
  13. Re: My happy cooperation with jinan acctek machinery!

    Thank you for the report - I am in the process of purchasing a Chinese router and am zeroing in on Acctek - a 6012 with vacuum table. Can I ask how you like the vacuum system? What controller did...
  14. Replies
    7
    Views
    557

    Re: XHC Ethernet Motion control card

    Good point, good support would be critical - especially for a greenhorn - I'm now thinking of ordering the machine with their standard controller and then upgrading to a US made card after learning...
  15. Replies
    7
    Views
    557

    Re: XHC Ethernet Motion control card

    Why's that?
  16. Replies
    7
    Views
    557

    XHC Ethernet Motion control card

    Hello I'm planning to purchase a Chinese router and am considering upgrading to an Ethernet interface - they offer this controller - the XHC. Does anyone have any experience with it? Please advise....
  17. Replies
    1
    Views
    474

    Anyone have an Acctek AKM6090?

    Hello I am considering purchasing an Acctek AKM 6090. I would like to hear from anyone who has one - how is running and how was it working with Acctek? Are you happy with it.? There seems to be...
  18. Re: Help finding a 6090 cnc router please advise

    Thank you reparrish47 for the lead! - Can I ask how you arrived at that machine? I'm discovering there are so many Chinese cnc manufacturers that make the 6090 out there, where do you begin?
  19. Help finding a 6090 cnc router please advise

    Hello I'm new to the group. I'm searching for my first cnc router - for professional wood working. I've decided on a 6090 with a base - not a bench top - such as the JCUT 6090 or the ACCTEK AKM...
  20. KL 6090 experience, please help with purchase?

    So now I'm narrowing down a new - and first cnc - down to a KL 6090 from Automation Technologies. It looks to be heavy duty at 500 lbs and it's comforting that they have a US warehouse and service....
  21. Replies
    1
    Views
    228

    Laguna IQ revisited - need advice please!!

    Hello, I just joined today because I'm sure I will need all the help I can get with a new CNC router. I'm a pro woodworker/furniture maker in Washington state and am looking to buy a cnc to develop...
Results 1 to 21 of 21