502,534 active members
5,194 visitors online
Register for free
Login

Search:

Type: Posts; User: drdos

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    17

    Re: Acceleration deceleration for spindle

    Parameter 4082, set in milli-seconds.
  2. Re: Display on A06B-6055 spindle drive shows "A". What does this mean?

    Hope this helps
  3. Replies
    2
    Views
    50

    Re: 935 SRAM ECC ERROR

    Replace your SRAM memory card in the controller.
  4. Re: How to activate Optional M code Victor Vcenter Fanuc 21i

    Remove 23 form 6075 then. The way Fanuc works if you use an M Code to call a sub then the ladder doesn't process that M code. You can then turn around a put M23 in the sub program then the ladder...
  5. Re: How to activate Optional M code Victor Vcenter Fanuc 21i

    There seems to be a bit of confusion here. You only put M-Codes in the parameter field if you want to call up a sub program. I would remove the 23 from P6075. What is it that you are trying to use...
  6. Re: FANUC Oi MATE-TD feedrate ovverride and handle not working

    You will have to look in the ladder to understand how the rapid over ride on your machine functions.
  7. Replies
    3
    Views
    57

    Re: Fanuc Ladder not logical

    This is a bit to understand but R9000.1 is on. The rung doesn't show it as it is the result of the function block directly above it.

    R9000#1 :Negative (input data<data compared) The input data is...
  8. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    Did it work?
  9. Re: Parameters for Conquest t42 w/Fanuc 18t model b

    Hardinge can provide thoes to you.
  10. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    Side Note: The PMC had a symbol for G43.5 but didn’t add it to the ladder. That is why you saw it on the PMC status page but not in the ladder. If you search it out now you will find it.
  11. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    As long as you have everything backed up then worse case you can clear memery and reload. Doubt that will happen. You do have to be in MEMORY mode for DNC to become active after you set your K-Bit.
  12. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    Here you go. Load it into the control and save to flash. Set Keep Rely K07 bit 0. 00000001 then you will have DNC. Make sure you are in memory mode to run as that is a requirment from Fanuc.
  13. Replies
    8
    Views
    115

    Re: Fanuc/Robodrill rapid feed parameters

    Parameter 1420, Must be in MDI or ESTOP and turn on PWE which can be found under the offset/setting screen under settings. Parameter Write Enable
  14. Re: Fanuc 10M MV Junior Zero Return Setting Gridshift

    Parameter 1241 is the parameter Heavy_Metal is referring to. If you don’t have a value in there then you are not using it. Try 1850 again; make sure that you move the Z axis far enough away from the...
  15. Replies
    2
    Views
    64

    Re: system P-G disk format

    Go to the R3 screen. Put floppy in slot 0 type DINT
    To Save:Go to RO mode, F7 key, 4 NL, 1 NL OK@file to save with a file name
  16. Replies
    3
    Views
    106

    Re: Custom macro programming

    Parameter 5001#0 TLB to 1 (Set Bit1 to 0 (TLB))

    TLC Tool length compensation
    0 : Tool length compensation A or B (Conforms to bit 1 (TLB) of
    parameter No. 5001)
    1 : Tool length compensation C
  17. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    Please Post the file that you downloaded via PMC I/O
  18. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    If it is not in the ladder you can't. Can you save the ladder and post it? You most likey will have to save it from the PMC I/O page
  19. Replies
    2
    Views
    93

    Re: Move without blocking other commands

    You will have to set it up as a PMC control axis. Not sure if the controller that you are using can support that. Fanuc does but you are going to have to use Fanuc motors and drives. How badly do you...
  20. Re: Any way to manually turn on G0043.5 / DNCI - its not in my ladder but *is* in PMC

    There is on the newer controls but yours you will have to edit the ladder or find in the ladder how to make it come on.
  21. Re: Need hardware descriptions manual for 15MA and PCM N manual

    you know iDOCs is 3 GIGs in size....
  22. Re: Help with with using an m code and canceling it with a macro

    Yes you are correct. You must have x20.2 go high (on) in order to fin out the M40.
  23. Replies
    2
    Views
    119

    Re: Using PCMCIA on Matsuura 30i

    It's the KEY SWITCH for program protect. You might want to check out Fanuc Program Transfer Tool software from Fanuc. About $20. It will allow you to drag and drop program file to and from the...
  24. Replies
    0
    Views
    91

    Re: Fanuc 16iM M99/M30 problem

    I have seen this if the ladder has M30 in the FIN line (G4.3 coil in the ladder)
  25. Re: Fanuc system 5M PMC Ladder and mapping recovery + retrofit??

    The 15 controller has a built in PMC editor. (Keep Relay K17.7) You can make all the edits you need on the screen. You have a PMC writer which you can burn directly from the controller if you have...
Results 1 to 25 of 464
Page 1 of 19 1 2 3 4