Search:

Hello COD: I'll contact Automation Technology to see if they can advise the resistor type and where I can buy it. The desoldering route will affect my E-Stop and L/Switches. Thank you

Sent from my...

Holly Platypus! I tried to connect a prove plate to my C-10 board (see attached jpeg ) from pin # 12 to the plate and ground connection to the spindle. However, the digitized light in Mach3...

First, I would like to thank the members who assist us newies in building our hobby machines. I'm finally assembling the components for 2 cnc routers and I've been learning about the limit switches....

Great, I'll be purchasing a new laptop with Windows 7 (probably one of those offered recently by HP) just for the V23 program. Thank you all.

Can I Transfer V23 to a new computer with Windows 7 or 8? My computer is extremely slow and in need for replacement. Thank you in advance for your assistance.

Well, I have great interest in anodizing, powder coating, aluminum casting together with cnc building. There's so much to learn and play with, but sssh the wife is watching!

Hello and welcome to our group. What is your group?

Hello "the.sniper": This week I received the anodized parts for the machine I'm building, the "EKFER DE LANCE" (110 parts). They have hundreds of holes and several pounds of stainless steel allen...

I second the motion! Apparently, Al likes what he does; enjoys helping others and thinks out of the box. The After Hours training videos are great. BobCAd-Cam got a winner!

179934Al, Thank you again. I was juggling with the idea of re-naming my first born "AL" in your honor or carving an appreciation plaque when my machine is operational. I think I'll prefer to do the...

Hi John, I didn't get the pm. Thank you for your invitation. Likewise, if you come to Miami I would like that. Attached are pictures of the "EKF- Dremel" I'm Building. Just last week I made the...

Prompt replies to questions and issues from a manufacturer is the litmus test of good customer service. I received a prompt reply from BobCad Product Manager Al DePoalo regarding a question I had. He...

Welcome to CNCZONE. Your machine work looks great. I'm from Miami. I built my machines but they are not operational yet until I send the components to be anodize. I would like hearing from you.

Hello Mr. Al DePaolo: I tried to activate the BobArt section of my V23 program but when I R/Click it, is greyed. I have not used this part of BobCad-Cam software since I purchased it. I don't have a...

Welcome: I didn't go with Misumi at this time but Bear5k highly recommends it. For my project I'm using Rockler t-tracks 36". I purchased their nuts and built my own t-track hold downs. I'll get the...

Hi, if the board you have is this one, this seller took the time to provide more information. If you don't get your answer from this drawing, try to get it by searching for 2m542 driver and...

You provided the answer I was seeking (that Milli Henry had to be a fine gal). I'll match/buy the motor of the 2m542 to the same MH of the 570 oz/in so that I can minimize overheating and get the...

I believe that you are correct in the error of the term. I checked other sites and I noticed that the information-some of the manufacturers provide-is confusing.

I do have another question: Can I...

I'm deeply thankful for the information. I will visit the sites listed. Now I can read the datasheets of other motors since you show me how the diagram connections work. I updated my previous picture...

Thank you for your rapid response.

The connection is for high torque.
The driver is a 2m542 4.2amps.
The breakout board is a HY-JK02-M 5 axis.
The motor is rated at 2.8 amps.
The PSU is...

Hello Esteemed Colleagues: I need your help in converting my 8 wire motor to 4. I do have the datasheet, but I don't understand the wiring diagram. Thus, I don't know which wires I have to connect...

Hi yello: please check Geof suggestion for aluminum. Use a cut-off disk for steel. Wear goggles! Good luck

I appreciate your message. However, it should have been addressed to Bear5k. He is the experienced one and the father of the twins. Keep in touch

I checked the 8020 T-Slots and also thought about making a drilled plate but these alternatives are too expensive. Then, I found Rockler.com. They have a 3/4 x 3" x 36" T-Track which gives 3 choices...

Hello hive8! sometimes you have to look at unrelated products to find the stuff you need. The parts in the picture look custom made for that specific manufactured item. Suggestion: Loot at drum set...

I just received the 5 sections of t-tracks I ordered from Rockler. They came in single plastic tubings. They look high tech, strong and beautiful with the anodized blue color. I'll try to incorporate...

Esteemed Bear5k, Not only you are a good machinist/engineer? but also a consummated poet. I researched my options and I opted for selecting the Rockler MultiTrack for my machine bed. The track...

Your question has merit. If it is aluminum extrusion, I have used a 10" compound miter saw (check it to be square!) with a metal cutting wheel. However, it gets very hot-so allow the wheel to cool...

Techno Inc. has exactly what I'm looking for (HEAVY DUTY EXTRUSION TABLE PLATE 20375). However, at US $341.00 it is beyond my purchase ability. I'll keep looking. Or, if you find an alternative ,...

Friends, I read from Bear5k today that Misumi has a heavier extrusion at a better price. I'll look into it. Again, thank you all for your assistance and recomendations.