check the voltage from the plasma cutter sounds like it is going up and down dirty tips and other things cause this
Type: Posts; User: jcoldon
check the voltage from the plasma cutter sounds like it is going up and down dirty tips and other things cause this
not sure what torch you can buy in your country hear in the usa hypertherm is the best torch to get it also is setup for machine control
with voltage devider out put the proma runs fine with a...
I under stand your frustration on the vital system site in the arch pro book you can down load there is a setup mode you can do to go through to make sure things work with out using the torch to...
its not the engraver I have a problem with I have an out put programed with over ride switch on screen works fine in mach 4
I just need to remove the M3 M5 spindle on command in the plate marker...
if you have he budget AKS cutting systems in cleavland ohio has a top table that can run 24 7
use a vital systems controller with there plasma screen the hilcon is one of the best industrial grade and works with no problems there support is tops . connect up some clear path motors to a 5...
buy a JD2 youll be happy
have you added any thing new wire exct it could be interference in the arch pro manual there is a test to make the proma simulate the torch voltage wile not using the torch try that to make...
I have mach 4 plasma with vital system arch pro screen with sheet cam the post processor that works is the mach 3 the others don't seam to work nether does the vital system one
my problem is...
I was looking to wire a proma to my miller 625 plasma cutter just to get things going then I get a hipertherm
the proma says it can wire to raw voltage I don't know if ita a good idea is there...
I currently wire my plasma table my question is the limit switches and home
I have 4 switches on the Y one on each side of the gantry Y + and one on each side of the Y-
and a X- and X+
my...
buy the biggest unit you can afford if your going to cut 3/4 steel then hypertherm 85 if not the 65 will do 85 is the biggest you can use on single phase power once you start the torch never...
put your computer on a ups it might be the power doing it ind make sure plasma voltage it isolated from the controller and computer
reading this it sounds like a controller problem maby another make controller like vital systems or mach motion they have the top controllers I know a new machine should have to do this
I...
I have a plasma table build I am doing its been a while I just completed the electronics I using a vital systems with gecko drive g203v with stepper nmea 34 model kl34h295 motor s
My question I set...
proma they have 3 different ones
check my youtube site koollakes showing how to make a rack drive and cheap gantry
I have been looking at vital systems seams everyone says they are a top dog for mach 3 and 4 this is a scratch build table also I finaly got the gantry dun and working on the gear racks almost dun...
what is the best cam program to use for a new be for plasma using mach4
any one use the HiCON Integra from vital systems I building a plasma and think this is a good controller
also want to use the proma thc thay have a new one using no relays
any input on this
can any one recommend a good controller for plasma I building a new one 60 tooth with 15 tooth gear reduction and a 20 degree rack I belive this should be fine . using nema 34 900 oz motors I was...
349898349900349902
I just wanted to get the gear reduction the best I could I found a 15 tooth 1/2 in shaft belt gear and a 60 tooth belt gear from what I read I be fine I using 900 oz 34 motors ...
I looking at using a 20 pitch rack gear 1 inch die . belt reduction 16 tooth on motor and 60 tooth on rack gear I believe that's 3.75 to 1 I have a 900 oz. nmea 34 hybrid stepper 8 wire with...
CHECK THIS SITE THEY HAVE EVERY THING YOU NEED Breakout Boards Archives - Stepper Motor | Stepper Motor Driver | CNC Router | Laser Machine | 3D Printers For Sale Stepper Motor | Stepper Motor...
any one using a computer with out a good ups is asking for trouble buy the bigust ups you can afford. they also monitor power and voltage with alarms take it from an electronic tech
your computer...
348542348544348546348548348550348552348554 just started my gantry got the rails on and ends started next the bearings and the racks
I had to make a jig to hold the v rail stock 3/8 then I had...
from the looks on the plans they are angels welded on the inside post likely to stiffen the bottom since there is no bottom they should be on the cut sheet to make you can always ask persision...
I building plasma table starting with the gantry my question. I am using a 3 x 5 11 gage tube what I am find the tubes are not very straight
I checked some 4x4 3x3 and the 3x5 all 6 foot long for...