Hi everyone,
I have an Amada Aries 222 with an Amadan O3P controller. The a few years in the middle of a job it shut itself down, didn't throw an alarm or anything, just powered down the...
Type: Posts; User: kluppy
Hi everyone,
I have an Amada Aries 222 with an Amadan O3P controller. The a few years in the middle of a job it shut itself down, didn't throw an alarm or anything, just powered down the...
Hi Everyone,
I am about to get back into fault finding this issue, does anyone have any suggestions where i might start? i have a second machine, we have swapped all the control cards (with...
well actually i could not find where it outputs +15 or -15 volts.
Hi Pitre,
Yes i did get the desired voltage levels and polarities at each point. i have attached a picture of the power supply. i don't have a schematic for the machine. it is a 1989 amada aries...
Hi,
all these LEDs stay light, along with all the other leds on the control panel.
Hi Pitre,
I have checked all the outputs of the power supply and they seem ok except the "control" pins, i can't find an output on that but I'm not sure if there is supposed to be either.
The...
Hi everyone,
I have an Amada Aries 222 with an Amadan O3P controller. The other day in the middle of a job it shut itself down, didn't throw an alarm or anything, just powered down the controller....
Hi everyone, quick question on what the resistance of a servo motor should be. The motors i have are Sanyo Denki brand. Specs are 75 volts, 350 watts and 5.5 amps. So, simple ohms law tells me that...
Hi guys,
Peter, yes i did end up buying the laser, it is a powerline RSM 130Q and we are based at Tiaro in Qld.
Wabbit, We have spoken to a number of people about it now and everyone says that...
hi everyone,
i'm looking at buying a second hand rofin yag laser that has a mark on the mirror from relection damage. we have seen the laser run and there are no obvious spots in the marking area...
hi everyone,
i'm looking at buying a second hand rofin yag laser that has a mark on the mirror from reflection damage. we have seen the laser run and there are no obvious spots in the marking area...
thanks very much guys, i'll try a few of these and get back to you.
hi,
i have recently bought one of the Chinese 6040 cnc routers. i am producing the drawing and G codes in bobcad V24 and using mach3 to run the machine.
i am engraving 316 stainless steel and...
sorry bill but where will i find these parameters on the machine?
hi guys, i tried putting in the settings that bill recommended but i had just one problem. i couldn't find the page to change the parameters! i found the machine set page but it didn't have an I/O...
thanks bill, i'll try these settings first thing in the morning and let you know how i go. again all your help is greatly appreciated.
Bill, the error that comes up says something about "did not recognise char" which i assume means characters, so i guess that could be the DC1 to DC4 setting you spoke about. i will get the exact...
do i need to have xon/xoff enabled?? in case you guys haven't picked up on it i'm a bit of a novice with this stuff. if you can recommend what settings i should be using i'm more then happy to...
thanks guys, yeah i need to figure out how to check the machine settings. any hints?
ok, so i've made the lead, belled it out and it's all cool. i connected the machine and the computer. adjusted my DNC settings on the computer to 9600, even, 7, 2, iso, iso, Xon Xoff. but it doesn't...
great!! thanks, i'll give it a try
hi everyone, sorry if this is a repeat question but i have just bought an Amada Aries 222 with a fanuc o3p controller. i would like to communicate with this machine via an rs232 cable and i was...