508,236 active members
2,620 visitors online
Register for free
Login

Search:

Type: Posts; User: johnansaro

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    20

    Re: mach3 and lathe

    Hi max

    Thanks for the reply.

    i know that I should use Mach3 or mach4 turn profile for turning, and I think lathe is similar to turning, but there are few things that I do not understand, for...
  2. Replies
    2
    Views
    20

    mach3 and lathe

    Hi there

    Is it wise or is it possible to use mach3 as a controller for a Lathe CNC 2 axis machine?

    also can I use artcam in order to generate code for my lathe machine? if you have a better...
  3. Issues on CNC Wood Turning Lathe Machine

    Hi there

    I am trying to put together a CNC Wood Turning Lathe Machine, It's Cutting dimensions are 1500*500 mm.

    I am planing to use Leadshine 85 N-m stepper for X and Y Axis, Is this motor up...
  4. Re: My CNC 3 Axis machine stops working "shutting down" after few minutes

    Hi Mactec54

    It is air cooled

    Vlotage = 220 v
    KW = 2.2 Or 3 Hp
    HZ = 3000
    Amps = 8.9

    Regards
  5. Re: My CNC 3 Axis machine stops working "shutting down" after few minutes

    Hi Mactec54
    Thanks a lot for the reply. I sort of figured that It should be a VFD programming program, I just wanted to make sure that I have no Mach3 setup problem, before i
    Check the VFD(The...
  6. Re: My CNC 3 Axis machine stops working "shutting down" after few minutes

    Hi There
    thanks for the reply.
    As matter of fact the spindle would not run with M3 S7000 or 10000 or 12000 .... It starts making a Hamming sound but would not run, But it actually Runs only and...
  7. Re: Spindle start only by Pushing the "spindle CW F5" Button and not by CycleStart Bu

    Hi There
    thanks for the reply.
    As matter of fact the spindle would not run with M3 S7000 or 10000 or 12000 .... It starts making a Hamming sound but would not run, But it actually Runs only and...
  8. Spindle start only by Pushing the "spindle CW F5" Button and not by CycleStart Button

    Hi There


    Every thing was working fine before, but after some moving of my shop and not working with my CNC machine it is acting a little strange

    In order to run my machining program my...
  9. Re: My CNC 3 Axis machine stops working "shutting down" after few minutes

    Hi There

    Thanks a lot for the replies, I think what awerby said was the issue, I reinstalled my win Xp and the match3, and It seems that it is working just fine, today I operated a 9000 line job...
  10. My CNC 3 Axis machine stops working "shutting down" after few minutes

    Hi there


    I have put together a MDF / Wood Cutting CNC Machine. It was working fine before after a I left it unattended for a while "few months"
    It as acting strangley, It shutts down and stop...
  11. Re: Spindle works only after closing and opening the mach3

    Hi every Body

    Please any recommendation would be greatly appreciated.

    regards
    Jhonansaro
  12. Spindle works only after closing and opening the mach3

    Hi there

    In my previous post I think i couldn't explain clearly my Spindle problem,
    My spindle works only after I close and open the mach3, By doing so (opening the mach3), I noticed that in...
  13. Replies
    0
    Views
    35

    Strange Spindle Behavior

    Hi there

    My spindle was working fine, but recently I had few Bearings replaced in my spindle and as result the machine was not working for few months.

    Today as I tried to startup my machine,...
  14. Replies
    2
    Views
    298

    Re: ATC Spindle How to set them up?

    Hi Gerry


    thanks for the reply
    this is what i thought to be, do you know what is the Script code that address them?
    The sensors are for:
    1: Chuck Closed
    2: Chuck open
    3: Running Spindle
  15. Replies
    2
    Views
    298

    ATC Spindle How to set them up?

    Hi there

    Could some one direct on how to set up an ATC Spindle, I am trying to Install a CC spindle, which is a copy of HSD,
    Just a general Guide I need,
    particularly on its sensors, do I need...
  16. Replies
    0
    Views
    215

    How to handle ATC Built in sensors

    Hi there
    I am trying to setup a tool changer.
    Apparently it has about 3 built in sensors, on which they check for If the Spindle is loaded (with tool or chuck) and if it is spinning and so on,...
  17. Re: Difficulty connecting to PWM section of my BOB from Mach3

    Hi there

    case resolved
  18. Re: How to find the right pin and Port for my PWM / and or Analog voltage output?

    Hi there

    Case resolved,

    Thanks
  19. Re: How to find the right pin and Port for my PWM / and or Analog voltage output?

    Hi there

    following are also some pictures of my...
  20. How to find the right pin and Port for my PWM / and or Analog voltage output?

    Hi there
    I am trying to install my 3 phase Spindle using a Delta 7.5 KW Inverter.
    At the moment I can connect to output1 of my BOB(Smooth Stepper) Trough Mach3 by pressing the (Spindle CW F5)...
  21. Difficulty connecting to PWM section of my BOB from Mach3

    Hi there
    I am trying to install my 3 phase Spindle using a Delta 7.5 KW Inverter.
    At the moment I can connect to output1 of my BOB(Smooth Stepper) Trough Mach3 by pressing the (Spindle CW F5)...
  22. Replies
    0
    Views
    239

    wait action in macros

    Hi there

    I am wondering what all these wait moves really mean, and how and where should they be used.
    I know that they are being used for causing some delays or wait action in macros while some...
  23. Re: strange behavior of servo motor and its driver

    Hi there

    Thanks a lot for your replies, and advice.
    As you mentioned, I have done some silly mistakes and 2 of my encoder cables were misplaced.
    and after I correct that mistake all is fine now....
  24. strange behavior of servo motor and its driver

    Hi there

    I am experiencing all strange things in my latest 2*4 CNC wood cutting Router project.

    The latest problem is as follow:
    All my four 750 Delta servo Motors were running nicely, at...
  25. Replies
    2
    Views
    247

    Re: Missing codes in auto tool changer

    Hi Gerry

    you provided the link of it your self, it is from the mach support.
    on this issue, do I need to use the M6End code, Please explain, and If I do, then how should i call it? is it in the...
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4