584,800 active members*
4,760 visitors online*
Register for free
Login

Search:

Type: Posts; User: garrett1812

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,124

    Re: Spindle turning at half speed?

    Solved!

    I set PD144 to 3000 and all is working now. Didn't even see this setting before, but someone pointed me in the right direction.
  2. Replies
    6
    Views
    1,124

    Re: Spindle turning at half speed?

    I just did a factory reset and put in these settings. Still the same results. Any other ideas?

    PD000 = 0 unlock settings
    PD001 = 2 command source RS485
    PD002 = 2 speed/frequency source RS485...
  3. Replies
    6
    Views
    1,124

    Re: Spindle turning at half speed?

    In my controller the min and max speeds are set to 0rpm and 24000rpm, respectively. I don't see any settings with speed in the VFD.
  4. Replies
    6
    Views
    1,124

    Re: Spindle turning at half speed?

    Thanks for all the feedback RoboDavo!
    My VFD is the Huanyang HY03D011B (110V, 3.0KW).

    1) No, I don't see any setting like this in the controller.
    2) I am not sure. I don't have this with any of...
  5. Replies
    6
    Views
    1,124

    Spindle turning at half speed?

    I have a Huanyang VFD and spindle connected to a Buildbotics controller, communicating by RS485. It seems to work okay, except for the speed. For example, if I request 10000rpm, the Buildbotics...
  6. Replies
    5
    Views
    1,469

    Yes.

    Yes.
  7. Replies
    5
    Views
    1,469

    Re: Huanyang VFD setup

    What other parameters should I set?

    Smaller VFDs were not available for purchase when I bought it, so I had to go with a 3kW.
  8. Replies
    5
    Views
    1,469

    Re: Huanyang VFD setup

    Bump!
  9. Replies
    5
    Views
    1,469

    Huanyang VFD setup

    Hi all,

    I have done some reading, and think these are the important parameters to set. Before I get started, can someone please check if these settings are correct, or if there is anything...
  10. Replies
    17
    Views
    2,377

    The spec says 110V single phase for the input, so...

    The spec says 110V single phase for the input, so I should be okay.
    It does also say 50Hz, and I am in the USA and use 60Hz, but the supplier said it was compatible.
  11. Replies
    17
    Views
    2,377

    I understand the maximum current draw can be...

    I understand the maximum current draw can be higher for the 3kW than the 1.5kW, but when using each to drive the 800W spindle, they’ll current draw should be about the same, correct?
  12. Replies
    17
    Views
    2,377

    Thank you!

    Thank you!
  13. Replies
    17
    Views
    2,377

    But that would be the same with a 1.5kW 110V VFD?

    But that would be the same with a 1.5kW 110V VFD?
  14. Replies
    17
    Views
    2,377

    Is the VFD really going to use more power when...

    Is the VFD really going to use more power when the spindle is only 800W?
  15. Replies
    17
    Views
    2,377

    Because it is lower cost and has a faster...

    Because it is lower cost and has a faster delivery than the 1.5kW version. Is there a reason not to use a larger VFD? Is it less efficient, or not compatible for some reason?
  16. Replies
    17
    Views
    2,377

    Re: Spindle and VFD pairing

    Great news, thank you. I am sure I will be back with more questions once I need to set it up.
  17. Replies
    17
    Views
    2,377

    Spindle and VFD pairing

    Would these two work well together, even thought the VFD is greatly larger than the spindle? I would not think this is a problem.
    ...
Results 1 to 17 of 17