Search:

Like I said, call FANUC. They’ll have all the part numbers at the ready, even if you don’t buy from them. I’ve called in many times and are more than happy to help even though you’re not having...

Just a side note, the three phases are A, which is PA and *PA, B phase which is PB and *PB, and the 1 rev pulse which is the Z phase pulse. If you had a breakout board and a o-scope, on your Honda...

Are you unable to input parameters in any way? You may have to manually input your 9000 series parameters first.

Do you have a parameter backup? If you don’t you’ll need to reach out to the machine builder and see if they have one on file. To get everything running you’ll need your CNC parameters and diags at...

I’m a little lost on what exactly you have, and what exactly you’re trying to have. What do you mean by pulse generator? When I hear pulse generator, I think of the MPG/handle.

I just recently...

There won’t be a CNC parameter for “coolant and blow air” but there probably will be a PMC parameter for it in the form of a keep relay, timer, counter, etc. Those PMC parameters are used by the...

I believe you are correct, that’s my bad

What is your control model? MSD-516 Is not a FANUC control. If you tell me your control model I can tell you what the part number for the parameter manual

You sent a picture of your I/O settings,...

Start by looking in the wiring diagram of the machine. Find the signal address for that button and then watch the ladder or signal status page to see if the contact/address is changing when you...

What is the port name on the servo drive unit? What is the part number of the servo drive? What voltage is that power supply sending?

I’m assuming the port is CXA2A and it’s supplying +120VAC...

Did your operator finish the Tool Recovery procedure? I’m assuming he did it through the “Quick NC” side of the control. That part program, O9040, is more than likely a protected macro program used...

There’s clearly some sort of interlock or combination of buttons that have to be pressed/held in order to home the axes. Those blinking LEDs will continue to blink until each axis is at its home...

You checked the motor power cables and motor separately for insulation? What were the values? Did you check the phase-to-phase resistance of the motor? It should be basically 0, like 0.3ohms.
...

What is the part numbers for the drive units? Is there a terminal bar on the the bottom of the drive unit PCBs? If there is, there would be 2 points, I believe 3 and 4, where 2 phase AC comes in....

Am I not mistaken or can't you just press the Offset key, go to the Setting page and change the relevant option from mm to inch?

Gonna need more info. Are there any alarms on the spindle module? Any alarms on the CNC or the servo module? What version control is this? Are you sure you hooked the servo module up correctly? Is...

I don't believe it's the F81 ROM giving the alarm if the socket is empty, I would think the alarm screen would show F81 indicating the ROM number, just like it shows OE1 when the main system software...

Yeah resetting the tool position can be a nightmare when the DGNOS/PMC data is lost. I haven't had to do it on a 3 control but I have on a 15 control. It's a huge pain

Alright so according to the procedure, I was really close. The switch it's referring to is a hardware deceleration switch. The axes cannot be on that switch when/if you attempt to home an axis out. ...

I’m not sure there is a parameter that contains the current time of the machine

For a 0i-TD, parameter 6710-6752 contains integer values of the count of machine parts along with operation time. If...

Check your electrical cabinet. There may be an old floppy disk or a printed copy of the part program. Unfortunately if you don’t have a backup, you may need to reach out to the MTB. Macro programs...

The LEDs over the individual axes are flashing because before they can be moved, they must be referenced. There should be a “REF” or “ZRN” mode button (reference and zero return, respectively) on...

If I’m not mistaken, the ATC data is going to be in your diagnostic parameters. The specific numbers depends on the MTB, Leawell in this case. How those numbers are interpreted is again based on the...

Did you check the incoming 3 phase voltage to the drive unit? I believe there should be a toggle switch for 230VAC or 200VAC depending on what you have coming in.

What is the control model? You...

On a 32i with WindowsCE, whether it’s a stand-alone or LCD mounted unit, there should be a blue rotary dial (looks like a potentiometer). When it’s set to 0, that’s normal operation. If you set it to...