Search:

Hay Thanks for all your info (HELP) but I'm going with a RS485 connection instead of using the MX4660 for spindle control. It will do what I want it to do, at least that what he said on the CNCnutz...

It is air cooled
the breakout board is a Lendshine MX4660
I will check on PD011

PD011=120

I did some research and found that one other user of the MX4660 was testing his Estop button and the...

Ok I see another Parameter problem with the minimum speed is your spindle air cooled or water cooled ???

PD011=120

What is the Breakout Board you are using[/QUOTE]

IQUOTE=mactec54;2329880]PD144=3000 not 2000 this should get you to your spindle max 18,000RPM with KeyPad control

If you are getting a PWM errors then you need to look at your wiring there could...

Jumper J1 in on 1-2
I will check PD044 and change it to 2
I will also check PD174 and set it to the correct amp of the motor not sure were it is at this time
be back at it tomorrow afternoon...

so I changed the wiring from the VFD to the MX4660 per the instruction from Leadshine manual and the spindle starts and is running at about 15000rpm no matter if I input a speed or just start the...

VFD is a Haunyang model HY03D023B 3ph 3.0KW 13A

controller is a MX4660 when I tested from this unit 0-10v after I run M3 s18000 I got no reading what so ever using my volt meter going to...

need some help with Chinese VFD also using MX 4660 and smooth stepper and Mach 3
i've double check the wiring everything is correct but I'm having trouble with the settings and Mach 3
if ...

Have you filled this request yet? and what time frame would there be?

Can someone tell me about the V-Clamp and if it passes the compressed air through, meaning that you would always be using air and dust would blow all over the place

Could someone advise me as what to use to hold up my 4" Vac hose when it is in it lowest saging position. Most likey to use some type of spring anybody got a idea? Thanks

Spilnde is from Shopbot I will send you more pictures

The far outside beam is adjustable, so I can adjust the liner rails to be parallel to the other side

Macona

I finally got my X axis up and running, now it is a 70Amp drive with a bigger motor for sure, can't tell you the size, but anyway here is my new problem, when jogging using Mach3 it will...

Macona
You should have wrote the manual.....I going to keep your instruction in the book. Thanks so much for you help, I needed it in the worst way.

I have attached a pic FYVP

Again THANKS...

Hi everyone you have visted this thread.

With all of your help I have been able to get the servos up and run and in both directions using Mach3. It would not have been so if you people did not...

Eric
I did not have time to call you this morning could you email me with your phone number

Macona

Just this morning I got the motors to run with the Serial cable and the software that is for the MR-J2S using a cable that is connected to the serial post of a computer and then to CN3...

Mach3 steps are 2000 and servo end coder count is131,072

Do you mean in Mach3 or in the Servo

Would I need to do something with the encoder setting in encoder/mpg?

Did check the wires for the step and dir, even switched them and still the motor moves slowwwww and the direction changed but always moves in the same direction for + and - moves

Can not get the servo motor to turn fast or reverse direction

Amp is a Mitsubishi MR-J2S-40A and HC-KFS motors

Finshlinewrx
Yes I have gone through the Mach3 motor tuning, and yes I have set the pins and ports. I'm connected with a Parallel cable to the BoB, also when I click on the X+ the Green light on the...

Hope someone can help me. I have a Mitsubishi MR-J2S-40A AC Servo Amp and motors. I have got this system off Ebay. I got directions has to how to wire it. and set it up with them instructions. I'm...

Hello From Thunderbit, Just doping a line to get me started. I do not have a CNC machine at this time but I'm just getting info to someday purchase a CNC Router. I wnat the best for the less, (don't...