584,837 active members*
4,895 visitors online*
Register for free
Login

Search:

Type: Posts; User: tahlinc

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    2,692

    This 30 year old cylinder has molded seals that...

    This 30 year old cylinder has molded seals that we did not even try to replace. We added a once of brake fluid to swell the seals and stopped the leak. Been good for two years so far.
  2. Thread: IPM Alarm

    by tahlinc
    Replies
    8
    Views
    4,880

    Solution: Replaced Z-axis drive. All is well.

    Solution: Replaced Z-axis drive. All is well.
  3. Thread: IPM Alarm

    by tahlinc
    Replies
    8
    Views
    4,880

    How do we identify the transistor module?

    How do we identify the transistor module?
  4. Thread: IPM Alarm

    by tahlinc
    Replies
    8
    Views
    4,880

    The drive shows 8.

    The drive shows 8.
  5. Thread: IPM Alarm

    by tahlinc
    Replies
    8
    Views
    4,880

    IPM Alarm

    Daewoo 300 Puma Lathe Fanuc 21T has 449 Z-axis INV IPM alarm in winter only. Works fine during the summer. In winter machine must be on for an hour in order to clear alarm. Anybody had this happen to...
  6. Replies
    9
    Views
    1,758

    Look on ebay

    a57l 0001 0037 | eBay
  7. Replies
    2
    Views
    2,692

    There should be a plastic line that comes down...

    There should be a plastic line that comes down from the top left of the head stock to a fitting on the side of the cylinder.
  8. Replies
    5
    Views
    2,679

    RAM Parity Error can occur when batteries are low...

    RAM Parity Error can occur when batteries are low and some of the memory gets corrupted. Check the voltage of the batteries on the door. Remember, you loose every thing when batteries are removed...
  9. Replies
    8
    Views
    3,457

    FANUC Magnetic Sensor Amplifier

    We found this problem caused by bad FANUC Magnetic Sensor Amplifier shown.
    Used ones are hard to find. New ones as more than $1000. Almost impossible to repair. Usually found inside the headstock....
  10. Replies
    0
    Views
    372

    Fanuc Repair guy

    Experienced Fanuc repair fellow needed.
    We have a 1987 Monarch C10 Slant bed with Ge Fanuc 10T that needs work on control. Located in Tucson AZ.

    Please cal 520-403-9002
    Jim
  11. This worked! (call with M66 P320 = 66) %...

    This worked!

    (call with M66 P320 = 66)

    %
    :9001(TOOL FETCH)
    #1=#4120
    #2=#4003
    G00
    G40G49
  12. Thanks! How are you calling 9000 and setting...

    Thanks!
    How are you calling 9000 and setting #149 global variable?
  13. Did you get an answer? Jim

    Did you get an answer?
    Jim
  14. Replies
    5
    Views
    3,111

    My 6M has Macro B. I a looking for documentation...

    My 6M has Macro B. I a looking for documentation on how to use it. My Smid book talks about "O" and later controls.

    Jim
  15. Replies
    2
    Views
    2,692

    Kiatmura Jig 7 Unclamp Cylinder

    Cylinder is not pushing drawbar far enough release pull stud.
    Construction of cylinder reveals that it is an air oil force multiplier. Perhaps oil is low so it does not develop full travel.
    Any...
  16. Replies
    2
    Views
    3,050

    Got it

    Thanks
  17. Replies
    2
    Views
    3,050

    Fanuc 10M Parameter pages

    Hi,

    I am looking for info on how to search for a specific parameter number, instead of paging with the arrow keys, on a Fanuc 10.

    Must be very obvious to all because no info on web.

    Thanks,...
  18. Replies
    32
    Views
    2,307

    I second that!

    I second that!
  19. Replies
    18
    Views
    4,427

    Squaring Kurt vise

    110 Ft-Lbs seems pretty high. Folks typically only tighten vise enough to resist the cutting forces. You would like the vise to move in the event of a crash.

    Procedure to square vise:

    Eyeball...
  20. Replies
    69
    Views
    9,788

    Scomm

    Hi,
    I just installed Scomm on XP and had no incidents. The program is nicely laid out. I am interested in incorporating comm into my Autocad abased cam program at the source code level.

    If that...
  21. Replies
    9
    Views
    1,758

    I do not have that board. Sorry.

    I do not have that board.
    Sorry.
  22. Replies
    9
    Views
    1,758

    I will check tomorrow. Thanks

    I will check tomorrow.
    Thanks
  23. Replies
    9
    Views
    1,758

    A57L-0001-0037-C

    The sensor is for a Kitamura Fanuc OMC.
    Jim
    520-403-9002
  24. Replies
    9
    Views
    1,758

    A57L-0001-0037

    We have the sensor but need the preamp!
    Jim
  25. Replies
    0
    Views
    2,619

    Arcs to Circles Lisp Routine

    Step import to ACIS solids (AutoCAD) from Parasolid yields a solid model that will have a 2D representation of holes as two arcs in order to show a circle.

    This AutoLISP routine will remove the...
  26. Replies
    4
    Views
    2,537

    You batteries should last several years.

    You batteries should last several years.
  27. Replies
    14
    Views
    4,712

    Another help is to Tap on the side of the chuck...

    Another help is to Tap on the side of the chuck at the same time.

    Jim
  28. Replies
    17
    Views
    5,417

    Letterease

    Sue Scott [email protected] has her husband's Letterease Autocad plugin.

    Expensive but good.

    http://www.softscout.com/software/Engineering/Computer-Aided-Design-CAD/Letterease.html
    ...
  29. Replies
    11
    Views
    1,835

    10 HP phase converter req'd

    Ben,
    Your 7.5 HP Interact CNC will need a minimum of a 10 HP PH converter to operate correctly. Bigger if you can afford it.

    Jim
  30. Replies
    31
    Views
    5,322

    Fanuc Drip Feed

    Excellent DNC that does drip feed.
    CodeShark lite $20
    http://www.softsquad.com/products.htm

    Cat 5 network cable makes good hardware handshake.
    Look at offerings:...
Results 1 to 30 of 55
Page 1 of 2 1 2