504,547 active members
4,527 visitors online
Register for free
Login

Search:

Type: Posts; User: bloke

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: Help!! First machine!!! new to me 2002 VM1 wont boot controller!!

    They seem ok. You may need to reload the software. Do you know which version you were running?
    Are there any disks in a folder in the back cabinet?
  2. Re: Help!! First machine!!! new to me 2002 VM1 wont boot controller!!

    Enter the BIOS pages and find the hard disk settings and post them here.
    You should have cylinders, heads, sectors, wpcom, lzone and the access type (lba, chs or similar).
  3. Replies
    3
    Views
    68

    Re: Hurco 2416 Freezes

    Check the CPU for burst capacitors.
    Remove all but 8MB of RAM. Swap around to see if the fault clears.
    Remove all I/O cards and the Canbus Controller (the keys won’t function with this removed).
  4. Replies
    3
    Views
    130

    Re: HURCO KM3 HELP!! Servo Fault

    SC is short circuit. Check the brushes on the motors and blow out the carbon dust to begin with.
  5. Replies
    3
    Views
    130

    Re: HURCO KM3 HELP!! Servo Fault

    What servo amps do you have?
    Any lights on them when it faults?
  6. Replies
    55
    Views
    538

    Re: Scary VM10U problems

    I had to sort out a coolant through spindle leak on a machine in Frankfurt that had the same model of Fagor encoder inside the head assembly. The encoder was half submerged in coolant that had been...
  7. Replies
    55
    Views
    538

    Re: Scary VM10U problems

    The clamping is performed by the air pushing a tapered cylinder into a similarly shaped recess in a split brake ring. This ring opens out very slightly to grip inside the housing. It is returned to...
  8. Replies
    55
    Views
    538

    Re: Scary VM10U problems

    I don’t know of any brass rings that seal the air accessory tube. There is normally a cap sealed over the threaded part down in the table.
  9. Replies
    55
    Views
    538

    Re: Scary VM10U problems

    The brakes on the rotary axes are actuated with air and released with a spring called an ‘anti-rotation ring’. Strip-down is simple and reasonably easy. Seal kits are available.
  10. Replies
    5
    Views
    163

    Re: VMX Tool Changer Leak and Lube Levels

    The oil you need is 120 to 150 ISO grade gear oil if you have the electric toolchanger. If you have the little perspex cover with the proximity switches then it's electric.
    to re-align the arm, put...
  11. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    I’ve just rebuilt a rack with almost exactly the same setup as you have. I’ll snag a picture of the finished unit on Tuesday. All you’ll need is the BIOS settings and a couple of other minor things.
  12. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    That Peak715 looks ideal.
  13. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    Do a search for Nexcom P777 or P715 CPU. You’ll find a processor that will fly. The 715 will be easiest to get started.
  14. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    Looking again at your pics, you have most of what you’ll need to get one going. One has the passive backplane but nothing else, the other has a DSP, Canbus Controller and a hard drive. Snag a CPU and...
  15. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    The older versions of software needed a dongle to run that matched the version of software running with it. Do you have anything connected to the parallel port (25 way D socket)?
    When you get up to...
  16. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    It’s a little tricky if you are trying to run the software after V2.15
    It may get sluggish as you get nearer to V2.30 upwards.
    You will need a few software tools to make it run and you’ll need to...
  17. Replies
    20
    Views
    330

    Re: Hurco Computer identification

    It shouldn’t matter. Everything depends on what you load on the hard drive. The second pic has an early Pentium motherboard instead of the passive backplane seen in the first pic.
  18. Replies
    4
    Views
    175

    Re: Need to buy encoder for Hurco BMC 4020

    Search for a ROD320.020-1250 or ROD320.020-2000 and see about changing the resolution in the CNC config parameters.
  19. Replies
    24
    Views
    620

    Re: VMX30 and BMC3017 question

    I don’t know yet. We still have Jatons at the minute...
  20. Replies
    2
    Views
    198

    Re: Hurco VMX 40 axis problem

    Have a look at the Y axis Servopack to see if the display is jumping around.
  21. Replies
    24
    Views
    620

    Re: VMX30 and BMC3017 question

    415216
  22. Replies
    4
    Views
    206

    Re: Need help with 1996 BMC4020

    Check the pulley is tight, the belt is ok and see if it comes back to 0.000 and has the little dot next to the Y on the position display. If it doesn’t, it is electrically miscounting.
  23. Replies
    4
    Views
    206

    Re: Need help with 1996 BMC4020

    Go ‘Auxiliary’ ‘enter’ 100 ‘enter’ then go to CNC config, Y axis and then look at the pages to find the ‘counts per revolution’ for Y and compare it to X.
  24. Replies
    101
    Views
    17,487

    Re: Hurco KMB1 upgrade

    You could get a 6000 RPM option for those anyway so I doubt the mecanical side of things would let you down. Motor-wise, It’ll either fly or die...
    Go for it! ??
  25. Re: BMC30 no response when start button is pushed in

    No. The control will regenerate them as required. They are not loaded as files on a new hard drive.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4